Kenmore 11087515110 Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 341241
Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.
Why this belt?
- Exact factory spec: 92 ¼-inch length × ¼-inch width, 4 ribs / 3 grooves - built to Whirlpool standards, not a generic copy.
- Broad compatibility: Fits most Whirlpool-made dryers - Kenmore 110-series, Roper, Estate, Maytag, KitchenAid, Admiral, Crosley, Amana & more.
- Quiet, durable rubber: Reinforced EPDM resists cracking and stretch for years of reliable tumbling.
Fixes these common dryer problems
| Problem |
How the belt solves it |
| Drum won’t turn |
Transfers motor rotation to drum |
| Loud squealing / thumping |
Replaces stretched or frayed belt |
| Burning-rubber smell |
New belt stops slippage & heat build-up |
| Damp clothes / long cycles |
Restores correct drum speed & airflow |
DIY install — about 15 minutes
- Unplug dryer; remove lint screen housing & front panel.
- Release belt tension at idler pulley; lift drum slightly to slide old belt off.
- Loop new belt around drum, idler pulley and motor pulley (ribbed side down).
- Re-assemble, run test cycle - enjoy quiet, consistent tumbling.
This part fixes the following symptoms
-
Heat stays on after drum has stopped
-
Will not tumble
-
Touchpad does not respond
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Broken dryer belt Bob B. • St Louis , MO • September 12, 2015
Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back...
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Whirlpool part
By: Whirlpool
Part Number: 349241T
Rear drum support roller kit for dryers. Mounts behind the drum to maintain alignment and smooth rotation. Replace when rollers are worn or damaged.
Do-It-Yourself Stories from Customers like You
Thumping/vibrating/rattling pretty bad fixed 100%! Doug P. • Durham , NC • November 15, 2015
I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a...
Read more
More
$18.23
- Compare At:
-
$21.51
- You Save:
-
$3.28
Genuine Whirlpool part
By: Whirlpool
Part Number: WP691366
Idler pulley maintains belt tension in your dryer drum assembly. Replace if the wheel is cracked, bracket is broken, or pulley has worn bearings.
This part fixes the following symptoms
-
Will not tumble
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Thumping/vibrating/rattling pretty bad fixed 100%! Doug P. • Durham , NC • November 15, 2015
I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a...
Read more
More
$15.95
- Compare At:
-
$18.82
- You Save:
-
$2.87
Genuine Whirlpool part
By: Whirlpool
Part Number: 279311
Dryer not heating or won't dry clothes? This igniter kit lights the gas burner. Moderately easy DIY repair with video guide—replaces failed igniters.
This part fixes the following symptoms
-
No heat or not enough heat
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
11 year old kenmore elite gas drye stopped working initial diagnosis: burner would light but would shut off in 3 or 4 minutes Jay W. • Dallas , TX • April 05, 2015
I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil...
Read more
More
$32.64
- Compare At:
-
$42.42
- You Save:
-
$9.78
Genuine Whirlpool part
By: Whirlpool
Part Number: 279827
Dryer won't start or stops mid-cycle? A worn drive motor is often the cause. This motor turns the drum and circulates air. Moderate DIY repair.
This part fixes the following symptoms
-
Will not tumble
-
Noisy
-
Shuts off too soon
See more...
Do-It-Yourself Stories from Customers like You
High pitched squeal: maybe a roller wheel maybe a bad felt bearing on drum maybe a rubbing fan wheel or just a burned out motor! Bruce K. • Pikeville , KY • September 06, 2014
My 12 year old Kenmore dryer problem started about 3 years ago with the motor just stopping.
My thing was:
I would turn it off and turn the drum by hand about halfway around and it would work again.
Last month, my wife said it stopped again and its making a loud noise,
but when I did "my thing" it still made a loud squealing noise (like I was killing a mouse).
I made time to work on it the next day, I took it apart, using the video instructions from AppliancePartsPros, I removed the top,...
Read more
More
$97.47
- Compare At:
-
$131.61
- You Save:
-
$34.14
Genuine Whirlpool part
By: Whirlpool
Part Number: 279570
The Door Latch Kit is an OEM replacement part for Whirlpool washers. This component is responsible for securely locking the washer door during the wash cycle, preventing it from opening unexpectedly and ensuring a safe and efficient operation.
Symptoms of needing to replace the door latch kit include:
- Difficulty in closing or latching the washer door
- Door opening unexpectedly during the wash cycle
- Leaks or water seeping due to an improper door seal
- Excessive wear or damage to the latch components
Causes of a faulty door latch kit can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the door alignment or strike plate.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.
This part fixes the following symptoms
-
Door won't close
-
Shuts off too soon
-
Doesn't shut off
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Dryer door latch worn out Kathy M. • San Diego , CA • February 22, 2015
When I looked up the part number there was a handy video that popped up. I watched the video and thought "how easy!" so, I ordered that part and waited. The next day, I thought I better start to take the door off of my dryer (because that's what the video instructed, and I wanted a head start) so as I was going into the garage to get my tools, my son came in with a small package. It was the part. That came, to quote another customer, "Crazy Fast!" All the way from Kentucky to California! ...
Read more
More
$8.56
- Compare At:
-
$13.85
- You Save:
-
$5.29
Genuine Whirlpool part
By: Whirlpool
Part Number: WP338906
The Flame Sensor is an OEM replacement part for Whirlpool gas dryers. This component plays a critical safety role by monitoring the presence of the gas burner flame during the drying cycle.
Causes of needing to replace the flame sensor can include normal wear and tear over extended use, exposure to high temperatures or corrosion, or physical damage to the sensor itself.
Symptoms that may indicate a faulty flame sensor include:
- The dryer not heating or producing heat properly
- Error codes related to the gas system or ignition failure
- The dryer shutting off unexpectedly during cycles
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas dryer models.
This part fixes the following symptoms
-
Shuts off too soon
-
No heat or not enough heat
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
11 year old kenmore elite gas drye stopped working initial diagnosis: burner would light but would shut off in 3 or 4 minutes Jay W. • Dallas , TX • April 05, 2015
I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil...
Read more
More
$35.95
- Compare At:
-
$42.78
- You Save:
-
$6.83
Genuine Whirlpool part
By: Whirlpool
Part Number: WP339956
Seals the lint screen housing to prevent air leaks and maintain proper airflow. Replace if damaged, missing, or causing lint buildup. Verify fit.
This part fixes the following symptoms
-
Takes too long to dry
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Gas dryer did not heat and excessive lint inside the unit James C. • New Boston , MI • July 20, 2017
Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered...
Read more
More
$9.63
- Compare At:
-
$11.36
- You Save:
-
$1.73
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694089
The Blower Wheel is an OEM part for Whirlpool dryers. This component is crucial for the proper circulation of hot air within the dryer drum, ensuring efficient drying of clothes by directing airflow through the drum and out the exhaust.
Common causes of a bad blower wheel include accumulated lint and debris obstructing the wheel, physical damage from foreign objects, or general wear from prolonged use. A faulty blower wheel can significantly reduce drying efficiency and may cause the dryer to overheat.
Symptoms of a bad blower wheel include:
- Longer drying times for clothes
- Unusual noises during the drying cycle
- Overheating of the dryer
- Poor airflow from the dryer vent
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not tumble
-
Takes too long to dry
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
Broken blower wheel on dryer Mark B. • Independence , WV • April 12, 2014
I FOUND the website on t internet, found my part ordered it and watched the how to video ,repaired the dryer myself. Awesome Website.
Read more
More
$34.75
- Compare At:
-
$41.35
- You Save:
-
$6.60
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8066184
The Motor Pulley is an OEM part for Whirlpool dryers, connects the dryer motor to the drum belt, enabling the drum to turn and efficiently dry your clothes. This pulley is crucial for the smooth operation of the dryer, ensuring that the belt is tensioned correctly and runs smoothly without slipping or causing wear.
Causes of a bad Motor Pulley include wear and tear from regular use, a buildup of lint and debris that can interfere with its operation, or a malfunctioning dryer motor that puts undue stress on the pulley.
Symptoms of a bad Motor Pulley include:
- Unusual noises coming from the dryer, such as squeaking or grinding
- The dryer drum failing to turn even though the motor is running
- The dryer taking longer than normal to dry clothes, which can occur if the pulley is not providing proper tension to the belt
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Broken motor pulley Michele D. • Jefferson , MA • December 11, 2015
Replaced pulley and belt.
Read more
More
$40.95
- Compare At:
-
$48.73
- You Save:
-
$7.78
Genuine Whirlpool part
By: Whirlpool
Part Number: W11415783
The Seal is an OEM part for Whirlpool dryers. This specific seal is designed to fit around the blower housing, ensuring a tight seal that prevents air leaks within the dryer. The blower housing is a critical component of the dryer's air circulation system, which moves air through the drum to dry clothes efficiently.
Causes of damage to the Seal can include wear and tear from regular use, excessive heat degrading the material over time, or improper maintenance practices that can cause physical damage to the seal.
Symptoms of a bad Seal include:
- Longer drying times than usual
- Excessive heat buildup in the dryer
- Unusual noises from the dryer, such as rattling or buzzing
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Gas dryer did not heat and excessive lint inside the unit James C. • New Boston , MI • July 20, 2017
Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered...
Read more
More
$16.95
- Compare At:
-
$20.34
- You Save:
-
$3.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694674
The Cycling Thermostat is an OEM part for Whirlpool dryers. It regulates and monitors the temperature inside the dryer during the drying cycle. It ensures that the dryer doesn't overheat and prevents potential damage to clothes or the dryer itself.
Causes of a faulty cycling thermostat can include wear and tear over time, electrical issues, or sensor malfunction.
Symptoms of a bad cycling thermostat may include:
- Clothes taking longer than usual to dry
- Inconsistent drying results
- Overheating or burning smell
- The dryer not heating at all
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This part fixes the following symptoms
-
Too hot
-
No heat or not enough heat
-
Shuts off too soon
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Dryer not heating properly Hashem N. • Los Angelos , CA • October 26, 2014
This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years.
Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy.
Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work.
I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I...
Read more
More
$48.46
- Compare At:
-
$57.67
- You Save:
-
$9.21
Genuine Whirlpool part
By: Whirlpool
Part Number: 49621
The Dryer Leveling Foot is an OEM part for Whirlpool dryers. It is designed to support and stabilize the dryer by allowing adjustments to the height and leveling of the unit. Proper leveling ensures the dryer operates smoothly and efficiently, reducing vibrations and preventing unwanted movement during cycles.
Causes of a bad leveling foot can include wear and tear from regular use, damage from moving the dryer, or breakage due to heavy loads and stress. Over time, the threads on the leveling foot can wear out, or the foot itself can become cracked or deformed.
Symptoms of a bad leveling foot include:
- Dryer rocking or wobbling during operation
- Unusual noises or vibrations
- Difficulty in adjusting the dryer's height
- Visible damage or wear on the leveling foot
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Took the base off the washer and dryer and they had no feet on them. Paula S. • Onalaska , WA • March 22, 2014
Bought the leveling feet and screwed them in the bottom and they work great.
Read more
More
$6.41
- Compare At:
-
$7.63
- You Save:
-
$1.22
Genuine Whirlpool part
By: Whirlpool
Part Number: W10874409
Dryer lint screen captures lint and debris to protect the blower system. Replace when torn, damaged, or handle breaks. Confirm fit by model number.
Do-It-Yourself Stories from Customers like You
Ripped lint filter Leo Z. • Arcadia , CA • March 18, 2017
Ordered replacement filter
Read more
More
$54.25
- Compare At:
-
$64.02
- You Save:
-
$9.77
Genuine Whirlpool part
By: Whirlpool
Part Number: WP691581
The Door Switch Lever is an OEM part for Whirlpool dryers. It plays a vital role in ensuring the dryer only operates when the door is securely closed by engaging with the door switch to signal the door's status.
Causes of a bad door switch lever can include normal wear and tear from repeated use, physical damage from accidental impact, or deformation from heat and humidity inside the dryer. A faulty lever can prevent the dryer from starting or stopping correctly.
Symptoms of a bad door switch lever include:
- Dryer not starting
- Dryer stopping mid-cycle
- Door not latching properly
- The dryer continuing to run with the door open
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Won't start
-
Doesn't shut off
See more...
Do-It-Yourself Stories from Customers like You
The lever to the door switch broke. Valerie M. • Rochester , NH • April 02, 2014
First, I rooked on YouTube for a video on how to fix it. The video brought me to a very helpful video with a link to your website. We have had this dryer since we bought the house 10 years ago and the thought of buying something new, that wasn't made as well was a dreaded thought. I went on the website, entered the model number of my dryer and then a search link for a parts search. Not knowing the part number, I was able to find the exact thing I needed. It was amazing and so easy! Had...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP348197
This support washer is a flat spacer used within the mechanism to support and separate mating parts, maintaining alignment and smoother movement. Replacing a worn washer helps reduce friction and wear so components operate properly. What it does:
- Maintains proper spacing and support between adjoining parts
- Helps prevent metal-to-metal contact, reducing scraping or grinding noises
- Addresses wobble or excess play when the original washer is worn, deformed, or missing
- Restores smoother movement and alignment in the assembly
What's included:
Install notes:
- Disconnect power and water supply before servicing; for gas combos, also shut off gas
- Refer to your model's parts diagram for location and orientation
- Track the order of any shims/spacers during disassembly and reinstall in the same sequence
- Tighten fasteners to manufacturer guidance to avoid deforming the washer or binding parts
Do-It-Yourself Stories from Customers like You
Screaching noise Linda Z. • Kailua Kona , HI • February 06, 2015
Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13