Kgrt607hbt Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

I have tried to remove the burner assemblies by removing the torx screws but they were badly rusted, and unfortunately they all were broken during removal. I just discarded the ruined orifices and assembled the new orifices and burner assembly. Read more

Orders set of four pads. Came in the mail about three days later. Replaced lost pad and it fit perfectly. Read more

Touch up paint Read more

Replaced It With New One Read more

• Noisy

Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine. Read more

I am a 42 year-old, reasonably handy woman with limited strength and a little arthritis in my hands, and I managed this all on my own, just. fine. Prep: Put an old blanket on a counter, because you will need to put the door OUTSIDE UP, INSIDE down on it with the hinges dangling over the edge of the counter. You will also need degreaser (I used straight white vinegar) if you want to clean things up while you have it taken apart. You will also need glass cleaner (or use vinegar and a microfiber... Read more

• Gas igniter glows, but will not light
• Little to no heat when baking
• Won't start

Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more

I ordered a new socket and replaced the socket and now we have a light in the oven. The project took about 10 minutes and was easy done. Read more

• Won't start

Replaced module: Although the new module was slightly different due to a third or ground terminal that was not on the original I managed to figured out that I did not need to worry about the ground since the existing wiring had already allowed for the connection. Easy repair. I ordered the part one day and it was delivered the next and that was using the least expensive delivery service. You guys are great Read more

Installed it according to video watched. Read more

I ordered the brioler pan for my new stove from y'all it was a little small but that's the part number in the book that I got with the stoveyall did a great job fast shipping just what I ordered will by from again thanks Read more

Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more

• Won't start

Of course, before disassembling anything, I unplugged and turned off the gas supply. To replace the spark electrode, I removed the drip pan/surface to gain access to the burner assemblies. Next, I unscrewed (with a 1/2" open-end wrench, I think) and disconnected the gas supply tubing from the burner assembly with the cracked electrode, and then unscrewed the assembly itself from the base surface. With the assembly detached, I flipped it over and removed the screw that secured the cracked... Read more

• Door won't close

Replaced the hinges after watching YouTube video. Read more

Replaced it with the part I got from you. Read more