Kitchenaid Khms155lss-1 Parts

Installed mounting bracket. Redrilled top screw holes. No template for hole locates but plenty of options to make sure you get a stud. Very easy to install. Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

I have used appliance parts pros before, their website is easy to use. I typed in the model and serial numbers, of course the number I have is rare, It did not show up on the list of models. It made me a little hesitant to submit the order. All three products came in the same box and on the same date it was promised. Just after opening the package I put everything in the microwave and I was relieved when everything fit perfectly. Read more

Very easy fix. Unplugged microwave, then lowered bottom panel, removed the two leads to the turntable motor, removed two screws attached to motor, removed old motor, put new spacer on motor stem, installed motor with same two screws, reattached the two wires, reattached panel ( after cleaning all the grease that built up over the last 6 years), plugged microwave in and good as new! Took me twenty minutes. Note: the two screws holding the motor were not Phillips like those holding the panel. So... Read more

Bought a new home with microwave venting into kitchen. Ordered damper assembly needed to vent through the wall to the outside. Removed microwave, followed directions in original installation instructions, turned fan over, cut hole in wall, installed wall cap and replaced oven. Problem solved. Read more

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

Well, I gotta say I was happy to find you still had parts for almost 20 year old microwaves. The microwave itself worked fine, so I hated to have to buy a new one, but I just couldn't take being hit in the head anymore; and my fix of using string and wire to tie it to the surrounding cabinets was unsightly to say the least. I'm glad I did some research and found this part - all I had to do was pop it in place and now the vent grill is secure. Problem solved with minimal cost. Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

• No heat

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

Quick replacement by sliding out the old filters and sliding in the new filters. Read more

Opened and changed after unplugging first. Read more

Installed mounting bracket. Redrilled top screw holes. No template for hole locates but plenty of options to make sure you get a stud. Very easy to install. Read more

Replaced lower door interlock bracket, cam(which was redesigned), spring(I believe this was the problem) and switch. When the door opens the spring moves the cam which releases the switch"on" Button which turns on the interior light when you close the door, the latch which protrudes out from door pushes into the cam which rotates to turn off the light switch and enables operation of the microwave. Old design cam would push past the light switch and the weakened spring would not push it back... Read more

I ordered a new magnetron and a new capacitor and after they arrived I set to work. I took plenty of pictures with my phone to remind me how the components came apart but it was pretty straight forward. Once the new parts were in and everything was reassembled the microwave worked good as new. The repair was less than a third the cost of replacement and no special tools are required. Just be careful to discharge the capacitor. This website is a great resource. Read more

I received the parts from parts pro within 3 days and everything fit perfectly nd all went well Thanks Parts Pro Wayne Mazur Joliet Il Read more