Kscs25fvms Parts

The Whirlpool refrigerator ice maker is a good design. The 8 32 screw was a problem I could not remove it with the thread lock it prevented me from unscrewing it. Therefore I replaced the shaft the splined hub and spacer washers. It seems to work fine now. Read more

Well with a lot of help from the world wide web and my friends from AppliancePartsPros.com, I was able to determine the source of the problem, which was the defrost thermostat. However, due to the disassembly involved to get to it, I decide to also change a couple of other parts involved in the defrost process, which are also located in the same compartment as the defrost thermostat. These parts were the thermistor and the defrost heater. Thanks to AppliancePartsPros.com, they had the parts I... Read more

Since it was one week before Christmas I thought it a good idea to clean the refrigerator before loading it up for the holiday. However once I was done, I found one shelf frame had cracked,which we super glued. But the deli drawer support was not able to go back in. So I scrambled online to find a solution. Your website was so helpful with the pictures and prior questions and answers that I felt confident I was ordering the right parts. Even ordered a door shelf that had cracked a while... Read more

Found the parts in the diagram of my fridge and simply installed it very easy Read more

The video was very helpful, but my KitchenAid model required slightly more steps. Only the two screws in front held the filter housing, same as the video shows, but it has to be removed from the rear. My model did not have the wire brace, only the two front screws held the housing. Shut the water off and pull the electrical plug. Remove the two screws holding the filter housing in the front. Remove the lower panel in the rear at the bottom of the refrigerator. Remove the two screws holding the... Read more

Replaced entire ice maker. A couple of important points. (1) The ice maker module does not include all parts. The door flap for example is not included. So save all plastic parts from the old unit including screws. The biggest installation problem was the power cable. There was little room on the side of the ice maker for the cable and connectors to fit. Make sure the connector that mates with the refrigerator cable is seated onto the plastic housing and does not stick out or dangle out.... Read more

Reviewed the AppliancePartsPros.com site and decided that the most likely suspect was the ice motor. I ordered one and got it FAST! I removed the water ice tray in the bottom of the Ice/water kiosk which exposed two phillips screws which I removed. The front panel came off by lifting upward and unplugging it. The ice door motor was visible near the top of the opening. I removed the hex head screws with a 1/4" nut driver so the ice door assembly was free. The core control board was hidden... Read more

Replaced icemaker and shutoff arm. Easy project. Read more

• Light not working

I saw your video on you tube and it seems very easy to do it my self, so I ordered the parts and I did it my self. It was very easy. Thank you for sharing with us on how to did it. One more thing, the parts arrived on the time they said it would come. Read more

Found the parts in the diagram of my fridge and simply installed it very easy Read more

My fridge was too cold - everything was freezing solid, even in the produce bins. The air from the diffuser vent was constantly running. After unplugging the fridge and plugging it back in, the diagnostic code on the control panel indicated that the air diffuser was not working. I purchased a new air diffuser, watched the very helpful video that showed how to install it, and replaced the part in about 10 minutes. The next day, I can tell that everything in my fridge has finally begun to thaw... Read more

Purchased new ice maker from Appliance Repair and replaced the old ice maker and associated parts that broke during attempted repair on my part. Replaced and is working fine. Read more

Ordered the parts, took door off the refrigerator. Removed all parts and replace with new parts. Took me about 15 minutes to complete. Read more

Replaced broken handle Read more

• Leaking

Thought leak was coming from icemaker but refrigerator was making ice just fine. had puddle on floor just below freezer door. upon closer inspection realized leak was coming from drain line. there were 2 pieces of tubing and the connector. leak was coming from where tubing goes into connector. wanted to replace it. didn't know what it was called. did live chat with someone I think was named James. he sent me diagrams and I could identify the part. once identified I ordered it. boom.... Read more

Myself Read more