Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Gray plastic retainer clip that secures tine rows to the dishwasher rack. Replace if broken, cracked, or missing to keep tine rows properly attached.
The parts I ordered came VERY quickly and fit perfectly. Read more
Fix water leaking from under your dishwasher with this pump volute. Directs water flow and prevents leaks with integrated seal. 20-minute repair.
I reviewed the schematic and saw the Volute Seal, and Impeller Seal were the two that were closest my source of water. After watching the video about changing the Impeller/seal I removed the motor, impeller, and volute; I found that the impeller seal was the faulty one in my case. Since I'd ordered the volute and impeller seal kits (as I wasn't sure which it was) I installed both while I had it apart. Runs great, no water - simple to do. The seal changes took about 20 minutes. The only... Read more
Covers and seals the rinse aid compartment to prevent leaks and ensure proper dispensing. Replace if damaged, melted, or missing. Verify fit with your model.
I found the part on AppliancePartsPros - great site, easy to use and quick delivery. This isn't a big deal - except I was able to do this without leaving my home! Read more
Door won't latch or close properly? The door latch strike secures your dishwasher door for a watertight seal. Simple 5-minute snap-in repair with video.
I ordered this part and switched the previously used one. Read more
Gasket for upper wheel.
With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)... Read more
If your dishwasher won't start, stops mid-cycle, or has no display, the control board may have failed. Moderately difficult repair, typically 30 minutes.
I initially purchased a door switch, thinking that it would solve the problem. I replaced the switch by removing the top 6 star screws, removing the component cover and removing one of the door switches (using a 3/16 socket) with the new one that I bought but I still had the problem. Looking at the schematic, the next part that needed to be changed is the electronic control board, which I purchased. I removed the same screws again and cover, used a screwdriver to pull back the clips holding... Read more
The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation. Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components. Symptoms of a bad power cord include:
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.
Read directions on how to change the power cord and watched video on your site on how to change the drain hose. Everything went perfectly. Read more
Fixes loose panels, rattling doors, or wobbly components caused by stripped or missing screws. Secures brackets, covers, and mounting hardware. Easy DIY.
Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find... Read more
Secures the upper spray arm assembly in the dishwasher tub. Replace if cracked, broken, or worn causing the spray arm to droop or become misaligned.
The upper spray arm mount on our KitchenAide dishwasher wore out, allowing the spray arm to droop into the dishes and pots in the lower rack. The replacement part was in stock and it arrived the very next day after I ordered it, with no special shipping cost. An amazing experience! The part took just 10 minutes to install--it could have taken less, but it always takes a few more minutes with a new fix. The washer is back in action, as good as new. I'm delighted with the response of... Read more
Quantity of ONE. Size: 8-18 x 5/8 inch. (#8 screw, 18 threads per inch, 5/8 inch long)
I ordered new seals from AppliancePartsPros.com. Finding the right seals was very easy, all based on model number of the appliance. While looking my unit over for other signs of wear, I noticed that a repair done by the prior homeowner to the lower wash arm was done improperly: a seal there was set protruding from the cover, the cover was missing screws, and the arm was missing the upper bushing. So I ordered a new seal, the missing screws, and both the top and bottom bushings (just to be... Read more
Secures tines in your dishwasher rack to keep dishes properly aligned. Replace this clip if it's cracked, broken, or missing to restore rack stability.
I searched the model on Appliancepartspros.com and ordered the items needed with overnight shipping. My order came the next day :) All parts were in stock and came clearly labeled and orderly packaged. Within 10 minutes my dishwasher was back in business and I was one happy camper. I would order from here again anytime and attempt to fixt the issue myself. Much cheaper that having somebody come out, only to tell you that they have to order the parts and come back at a later time to fix the... Read more
The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.
Pulled a video from online and ordered my parts from Appliancepartspros.com. This was the second repair I've done with your help, the last being my washing machine. This time I replaced the dishwasher detergent dispenser on my Kitchen Aid. You guys make it so simple and give me the confidence to do it myself! Read more
Grey vinyl touch-up paint for repairing chipped, rusted, or damaged dishwasher rack coating. 4oz bottle with brush. Restores protective coating.
Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure. Read more
Black access panel kit for dishwasher lower front area. Replaces missing, cracked, or damaged toe panel assembly. Secures under cabinet for finished look.
I found the part number, double checked it, and ordered the part, which arrived as promised. However, the part was just placed in a folded cardboard tube and was damaged by the shipper. I figured it was only a toe-kick, so I bent the part as best I could and installed it in 3 minutes. Read more
This power cord connects your appliance to a household outlet. Replacing a worn or damaged cord restores safe, reliable power and can help resolve no-power or intermittent power issues caused by a compromised lead.
Awesome company! Very quick, good price and the right parts. Would order again no question. Read more
Drain hose connects dishwasher pump to exterior drain. Replace if cracked, leaking, chewed by rodents, or when check valve fails. Includes elbow connector.
I figured out that it was probably a plugged pump hose, since the pump would run, it somtimes it drained and sometimes it didn't. Your video helped with how to take the dishwasher out and replace the hose. I replaced the hose and everything is now working fine. It turned out to be a broken check valve in the old hose that caused the problem. It took 90 mins to do the repair. Read more