Lat 7304Aae Parts

My husband is a natural handyman, I call him Bob the Builder (don't tell him I told you that!). When our washer started leaking we started looking for a used one online, when that didn't work he figured he'd take it apart and see if he could find the problem himself. Well after doing some research online we replaced the drain pump, which in the long run was a good idea because ours wasn't in very good condition, but our washer still leaked. So after some more looking around he found a hole on... Read more

Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more

Removed the front panel and removed the screw from the console which revealed a broken plastic tab on the right side of the old injector. Replaced the old injector with the new one and that took care of the problem. Read more

Found the parts in the diagram of my fridge and simply installed it very easy Read more

Replaced mounting stem and tub bearings Read more

I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more

The washing machine intermittently would not agitate or spin. A reset of the timer dial fixed it. Then nothing fixed it. Originally thought it was the timer but father wanted to check out other possibilities. So he brought his meter over and went through all that he could, including checking power to the motor below. All was good electrical-wise. On the holiday, January 1, a rep. at AppliancePartsPros assured me that if a new timer did not fix the problem, I could return the item, even... Read more

Replaced flow meter and control valve Read more

• Lid or door won't close

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

We ordered parts from appliance parts pros and I fixed it. Read more

I ordered the required parts from your website, the parts required were easily identified from the website tub blowup. The parts were delivered within 2 days and installed within 15 minutes Read more

I called AppliancePartsPros and gave them the detail of my problem and that I thought that the timer may be bad. The guy on the phone with me talked to the technical group and came back and told me that they thought that it was the timer. The timer was ordered and the price was $50 cheaper then a local rep here at home. Anyway the part was ordered and came in less then 2 days and when I replaced it the problem was taken care of. The service, price, and time to get the part was great and I... Read more

After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap... Read more

• Noisy

Replaced them. Read more

Went on internet, found a great site and learned that the cold water hose filter was very much clogged at the machine intake. Cleaned it and voila. Ordered an extra filter from Appliance Pros.com and literally was amazed that it arrive within 2 days of my internet order. Great efficiency and customer service….great experience. Will definitely use them in the future….thank you! Read more

Replaced the tube and the clamp Read more