Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer won't start or spin? A faulty lid switch prevents operation when the lid position isn't detected. Simple clip-in replacement, typically done in 10 minutes.
Took off the back of the top pushed the switch forward and lifted it out after I unplugged it. Put the new switch in the opposite of how I took it out, plugged in the wires put the back on and finished my laundry. Read more
Indicator light lens covers the pilot lamp opening on your range control panel. Replace when cracked, discolored, or missing to restore visibility.
Purchased the triple burner and dual burner element. I added my model of stove and I was able to pull up diagrams of the stove parts. The parts were easy to find using the diagrams and the burner elements were marked 17 & 15 so I placed my order. Parts were here in a couple of days. The tricky part was figuring out how to get into the stove top. I was a few youtube videos to see different replacement. My husband and I got the stove top off and flipped it over on the counter. We looked at... Read more
This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.
Replaced the tube and the clamp Read more
Hose clamp for securing water supply and drain hoses on the washer. Provides leak-free seal at hose connection points.
Replace faucet adapter, replace fill and drain hose assembly. You must remove outer cabinet to be able to route new hoses and access hose connections under tub. Read more
Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.
I followed the Appliance Parts Pro's advice videos for the Maytag MAV6451AWW Atlantis washer on replacing the snubber ring and the suspension springs. Everything went just fine except replacing the two rear most suspension springs. None of the videos illustrated REINSTALLING the REAR springs which is extremely difficult because you can't get enough leverage with your arm extended. Observing my frustration, my wife recommended taking off the back side. You can't simply take off the back,... Read more
Seals the top of the outer tub to prevent leaks and splashing. Replace if cracked, worn through, or gasket is compressed causing water to escape onto the floor.
Removed the old tub cover/gasket by removing the front panel and top lid. Then, unclipped the tub cover. Read more
Washer won't start or spin? A broken lid switch actuator prevents the safety switch from engaging. This plastic striker restores proper operation in 5 minutes.
Replace the broken switch Read more
This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
Leaking water at the tub ring during fill? This lower water injector channels incoming water into the tub. Simple 30-minute DIY repair with basic tools.
An easy fix for the most part. I had no idea what I was doing, but glad I bought both upper and lower injectors. Not sure why these are separate parts? Cheap plastic. I did not get the hose clamp because I didn't think I would need it. You probably do, so go ahead and just order it or grab one if you have one laying around. Mine is hooked up without it for now which I'm sure I will regret later but I needed to get our washer running immediately due to a bed bug situation in our house. Read more
Fix a washer that won't advance through cycles, fills but won't spin, or stops mid-cycle. This timer controls wash, rinse, and spin sequences. 30-minute DIY repair.
Replaced the main timer / control. Read more
Replacement mounting bolt for washer outer tub assembly. Secures tub components together with nut. Replace if rusted, stripped, loose, or missing.
We watched the video before we purchased the parts for this project. We wanted to make sure exactly what parts we would need. Thanks for having this information available. We purchased the mounting stem repair kit,,tub bearing kit, 3 new bolt/washers that hold the outer tub in place and the spanner wrench. Cleaned everything... NOTE :TAKE THE TIME TO CLEAN YOUR FILTERS ON THE BOTTOM. Thing went back together smoothly. We refereed back to the video when in doubt. Total repair $118.00... Read more
This washer drain hose routes wastewater from the drain pump to your standpipe or laundry tub. Replacing a cracked or kinked hose restores reliable draining and helps prevent leaks during the spin/drain cycle.
Bought a new hose and took one small cover off the back of machine, used pliers to remove clamp, took off old hose, put on new, replaced clamp, replaced cover and was done. Five minutes tops. Read more
This lid bumper cushions the contact point between a washer lid and the top panel to reduce slamming noise and protect the finish. Replacing a worn or missing bumper restores smooth, quiet lid operation and helps prevent paint damage.
Removed lid sanded down all rust spots, taped over the printed instructions on the inside of the lid, washed with alcohol and spray painted with appliance white epoxy paint. Replaced the plastic hinge-balls and one of the lid support/bumper grommet. It was actually easier to install the lid than removing it; used a small amount of grease to hold both balls in place, by holding the lid vertical and placing the left side to the inserted ball and then pushing the right side down. The lid slides... Read more
Small drive gear inside the washer transmission gearcase that meshes with mating gears. Replace when worn, stripped, or damaged to restore power transfer.
American appliances are very easy to fix in comparison to imported ones. Just open the washer and take de transmission cover out change the pinion inside removing a simple retainer. In the agitator there is a screw that you loosen it take it out, then de tub and take the shaft out and put a new seal and a new c clamp and reinstall everything back. Top-loading washers are very easy to fix in comparison to front-loading washers that are very difficult to fix. Read more
This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.
Removed old water valve and replaced it with new one. Reconnected wiring and water lines. Everything is working fine now. Read more
Replace this washer gasket seal to stop leaks between components. Worn gaskets cause water leakage and poor performance. Verify fit with your model.
We ordered parts from appliance parts pros and I fixed it. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.