Lat 9704 Aae Parts

Specs: 10-16 x 1/2 inch.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This washer timer regulates the order and length of each wash, rinse, and spin stage by sending power to the right components at the right time. Replacing a failed timer restores proper cycle advancement and dependable operation.

• Sequences wash, rinse, drain, and spin through the complete cycle
• Directs power to the drive motor, water inlet valves, and drain pump as programmed
• Common symptoms it can help resolve: cycle won't advance, stops mid-cycle, runs longer than expected, or is stuck on one setting
• Mounts in the control console and interfaces with the cycle selector knob

• Disconnect power before servicing; verify controls are off
• Access the console; photograph or label wiring, then transfer wires to the new timer one at a time
• Secure the timer, reassemble the console, and align the selector/indicator
• Run a short test cycle to confirm proper advancement; check the lid switch and wiring

The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order 22003428.

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

Leg, adjustable (w/nut)

This top-load washer agitator shaft collar fits on the drive shaft to locate and secure the agitator. Replacing a worn collar restores proper alignment and engagement, reducing wobble and helping maintain consistent wash action.

• Positions the agitator at the correct height on the drive shaft
• Helps ensure positive engagement so the agitator moves as designed
• Maintains alignment to minimize excess play and noise
• Common symptoms of a failed collar: loose or wobbly agitator, rattling/knocking during wash, weak or intermittent agitation

• Disconnect power and water supply before servicing
• Remove the agitator to access the collar; note the original position for reference
• Install and secure the new collar per the manufacturer procedure; verify proper alignment and minimal play
• Reinstall the agitator and run a brief test to confirm smooth operation

This replacement seal restores a tight, leak-resistant barrier between mating parts inside your appliance. Replacing a hardened or damaged seal helps stop seepage and keeps the system operating as designed. What it does:

• Forms a tight barrier between components to contain fluids and prevent leaks
• Helps maintain proper pressure/flow at the sealed joint
• Reduces risk of moisture damage around the connection point
• Common signs it's worn: drips or puddles, dampness around the joint, musty odors, visible cracking or flattening of the old seal

• 1 seal

• Disconnect power and shut off water or gas supplies before servicing
• Access the sealed joint; remove the old seal and clean mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved lubricant; install without twisting
• Reassemble, restore utilities, and check closely for leaks during initial operation

For complete assembly order WP206680.

This rubber seal creates a tight barrier between mating components to keep water contained and stop drips. Replacing a flattened or cracked seal helps prevent leaks and protects nearby parts from moisture-related damage. What it does:

• Forms a watertight gasket between two parts in the assembly
• Helps prevent drips or seepage at the connection point
• Restores proper compression when the original seal hardens or deforms
• Common signs of failure: leaks, dampness, or visible cracking/flattening of the old seal

• 1 rubber seal

• Disconnect power; for water-bearing assemblies, shut off the water supply
• Access the seal location per your service information and note orientation/depth before removal
• Clean mating surfaces; lightly moisten the new seal with water or mild soap to ease installation
• Ensure the seal is fully seated, reassemble, and test for leaks

Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.

This water level switch senses tub pressure to control the fill. The infinite rotary style lets you set the level precisely; replacing a failed switch restores correct fill shutoff and proper cycle transitions.

• Monitors air pressure from the tub and stops water at the selected level
• Signals the timer/control to advance from fill to wash and later to spin
• Helps resolve symptoms like overfilling/continuous filling, underfilling, or inaccurate water levels
• Prevents stalls where the cycle won't advance from the fill stage

• Disconnect power and turn off water supply before servicing
• Remove control knob and console panel to access the switch
• Transfer wires one at a time to matching terminals; move the pressure hose to the new switch and ensure a snug, leak-free fit
• Mount the switch, reassemble the console, restore power/water, and test a fill cycle

This is the timer that is used on washing machine units. The purpose of the timer is to control the electrical components and the duration of the cycles.In the event that the washing machine does not progress through the cycles, it is likely that the timer is bad and will need to be replaced. Some users report that the washing machine will go through the washing cycle but will not drain or spin. The replacement process is fairly easy and can be done quickly. It is important to unplug the washing machine from the electrical outlet before starting the replacement process. Wear work gloves during this process to protect from scratches or other injuries.This particular timer is compatible with washing machine units that are manufactured by the Maytag brand. It is sourced directly from the manufacturer and is sold individually. It is a genuine OEM replacement part that is high-quality.

This factory replacement screw fastens the specified components in your appliance as shown in the parts diagram. It restores a secure fit and helps eliminate looseness, vibration, and noise when an original fastener is missing, stripped, or corroded.

• Secures panels, brackets, and assemblies at the locations designated for your model
• Direct replacement for the original fastener to maintain proper fit and alignment
• Replace when threads are damaged, head is rounded, or rust is present
• Common symptoms: loose or rattling parts, gaps/misalignment, increased vibration

• Disconnect power and shut off water supply if applicable before servicing
• Refer to your model's parts diagram for exact location and quantity
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug firmly but do not overtighten to prevent stripping

This washer lid switch signals that the lid is closed so the cycle can run. A failed switch can keep the washer from starting or spinning. Replacing it restores safe operation and consistent cycle performance.

• Senses lid position and enables operation only when the lid is closed
• Interrupts spin when the lid opens to meet safety interlock requirements
• Typical symptoms: washer won't start, won't spin, or stops when the lid is bumped
• Intermittent operation that improves when pressing or holding the lid closed

• Disconnect power before servicing; allow moving parts to stop completely
• Access the switch from the top/console area as directed for your model; note wire-harness orientation
• Secure the switch and ensure the lid strike aligns properly with the actuator
• After reassembly, run a spin test with the lid closed to verify operation

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose