Lesa907pbl02 Parts

The defrost drain pan collects water that melts off the evaporator during automatic defrost and holds it near the warm compressor so it can evaporate. Replacing a damaged pan helps prevent leaks, puddles, and odors around the base of the refrigerator.

• Collects defrost water routed from the evaporator drain
• Positions water in warm airflow near the compressor for evaporation
• Replace if the pan is cracked, warped, missing, or leaking
• Symptoms can include water on the floor, moisture under the unit, or musty odors

• Unplug the refrigerator; wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the pan near the compressor
• Lift out the old pan; transfer any reusable clips/brackets; seat the new pan under the drain tube and ensure it's level and clear of moving parts
• Reinstall the panel, restore power, and check for proper drainage and evaporation

The Convection Fan Motor Kit is an OEM replacement part for Frigidaire ovens. This kit includes the motor responsible for driving the convection fan, which circulates hot air within the oven cavity to ensure even cooking and consistent temperatures during convection baking or roasting.

Over time, causes of a bad convection fan motor can include electrical wear, overheating due to heavy use, or damage from grease or debris buildup. Additionally, worn-out bearings in the motor can impair its performance.

Symptoms of a bad convection fan motor include:

• The fan not spinning or operating inconsistently  
• Uneven cooking results in convection mode  
• Strange noises such as rattling or grinding during operation  

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Note: Convection fan motor 5304467898 replaces earlier fan motors with a cooling blade. The fan motor doesn't include the cooling blade as it is no longer required.

This is the drive gear for the ice maker module. It transfers motor power to the ejector/harvest mechanism so cubes release consistently; worn or stripped teeth can cause clicking, stalls, or little to no ice production.

• Transfers motor torque to rotate the ejector and complete the harvest cycle
• Replaces a cracked, stripped, or worn gear that prevents proper ice ejection
• Typical symptoms: no ice production, icemaker stuck mid-cycle, clicking or grinding from the module
• Helps restore reliable ice maker cycling

• Unplug the refrigerator before service; turn off the water supply if moving the icemaker
• Remove the icemaker assembly for access; note the original gear's orientation before removal
• Align the new gear with the shaft; do not force it—inspect mating parts for wear
• After reassembly, verify the ejector turns freely; restore power and run a test cycle

This ice crusher blade (#2) mounts in the freezer's ice bucket assembly. It helps break up cubes for the Crushed Ice setting and can restore smooth dispensing when the original blade becomes bent, dull, or broken.

• Mounts inside the ice bucket crusher to slice/crush cubes when Crushed Ice is selected
• Helps maintain consistent ice flow and size through the dispenser
• Wear or damage may lead to no crushed ice, only whole cubes dispensing, jamming, or grinding noises
• Visible bending, dull edges, or a missing blade are common failure signs

• Disconnect power and remove the ice bin from the freezer
• Disassemble the crusher housing to access the blades; note the order/orientation of blade #1 and blade #2 before removal
• Wear cut-resistant gloves—edges are sharp
• Reassemble in the same order, tighten fasteners, reinstall the bin, and test the dispenser

This is a refrigerator shelf that provides a sturdy, flat storage surface. Replacing a cracked or missing shelf restores usable space and helps keep items organized and properly supported.

• Supports food items and containers in the freezer compartment
• Helps maintain organized storage and clear airflow
• Replaces damaged, cracked, or missing shelf to restore capacity
• Common symptoms: broken glass, sagging or missing shelf, unstable items

• Unplug the appliance and wear cut-resistant gloves
• Allow the glass to reach room temperature before handling
• Remove any retaining trim/rails, slide out the old shelf, and seat the new panel fully
• Confirm the shelf is level and locked into its supports before loading

The Glass Shelf is an OEM part for Frigidaire refrigerators. This component provides a stable and durable surface for storing food items within the refrigerator, helping to organize the storage space efficiently. The glass measures approximately 16” by 11.25”.

Over time, the glass shelf can become damaged due to heavy items being placed on it, accidental impacts, or thermal stress from temperature changes. Replacing a damaged shelf ensures safe and effective storage inside the refrigerator.

Symptoms of a bad glass shelf include:

• Cracks or breaks in the glass
• The shelf not fitting securely or wobbling
• Difficulty in cleaning due to damage
• Potential for food items to fall due to an unstable surface

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement part is a gasket seal, and it is intended for use on ranges and ovens. This is a genuine replacement part made by Frigidaire. This gasket is an important part of any range or oven. This part is used around the opening of the oven so that it is sealed when in use to prevent heat loss while cooking. A new gasket seal might be needed if the current one is visibly falling off, frayed, or not attached anymore. This is a genuine OEM replacement part and is sold individually.

This clip mounts to the refrigerator liner and secures the crisper cover/slide rail so the drawer stays supported and glides properly. Replace a broken or missing clip to restore alignment and smooth operation of the crisper.

• Holds the crisper cover/slide rail firmly against the cabinet liner
• Supports the crisper drawer to prevent sagging or tilt
• Helps restore smooth opening and closing of the crisper drawer
• Common symptoms of failure: loose rail, drawer off-track, difficulty sliding, or a cracked/missing clip

• Unplug the refrigerator or disconnect power before servicing
• Remove the crisper drawer and cover/glass to access the clip
• Release the old clip (snap tabs or screw), align and secure the new clip; reuse the original fastener if your model uses one
• Reinstall the cover and drawer; the drawer slides freely

Note: Due to a factory change, the new glide may be shorter than your original. Per Factory: The original part was 19.75". The new part is 16.25" and will install and function the same.

This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.

• Directs power to the associated circuit when switched on or off
• Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
• Helps restore positive, consistent control from the backguard/control panel

• Disconnect power at the breaker before servicing
• Access the switch from the control panel/backguard; retain screws/clips
• Label/photograph wire positions and transfer leads one at a time to the new switch
• Ensure firm terminal connections, reassemble, restore power, and test operation

This ice crusher blade (#3) fits inside the refrigerator's ice bin crusher stack. It helps break cubes into crushed ice when selected, restoring smooth, consistent crushed-ice dispensing if the original blade is bent, dull, or missing. What it does:

• Works within the ice bin's crusher assembly to fracture cubes into crushed ice
• Engages with the auger and spacers as part of the blade stack
• Worn or damaged blades can lead to only cubes dispensing, weak crushing, jams, or scraping noises
• Visible bending, chips, or rust are common signs it needs replacement

• One crusher blade (#3)

• Disconnect power and remove the ice bin before service
• Empty the bin and carefully disassemble the crusher stack; note the exact order and orientation of blades, spacers, and washers
• Wear cut-resistant gloves—blade edges are sharp
• Reassemble in the same sequence and verify the assembly turns freely before reinstalling the bin and restoring power

Replace a failed refrigerator control board to restore dependable operation. This electronic board supplies the logic and switching for the features it manages, helping eliminate intermittent or unresponsive behavior and returning the appliance to consistent, predictable performance.

• Interprets inputs from sensors and switches, then controls connected components through onboard relays
• Coordinates timing and operation of the functions this board manages
• Can correct erratic cycling or unexpected shutdown of controlled functions

• Disconnect power to the refrigerator before servicing
• Use ESD protection; handle the board by the edges and avoid touching components
• Access location varies by model; transfer connectors one at a time to the new board and secure in the original mounting
• Restore power and allow the unit time to resume normal operation

This electronic oven control board governs bake/broil functions and the display for Frigidaire-made ranges. Replace it to restore oven heat, accurate temperature regulation, and responsive controls when the original control fails. What it does

• Controls power to the bake and broil element/igniter and times oven cycles
• Monitors the oven sensor and maintains the set temperature
• Receives keypad inputs and drives the clock/temperature display
• Common symptoms: oven won't heat or overheats, display dead/dim, unresponsive buttons, intermittent shutoff, or error code on the display

• 1 electronic control board

• Disconnect power at the breaker before servicing; verify no voltage at the range
• Access the control through the backguard/control panel; photograph wiring for reference
• Handle the board by the edges to avoid static damage; move connectors one at a time
• Transfer the existing keypad overlay/trim and any mounting hardware from the old board

An ice auger rotates inside the freezer's ice bin to move cubes to the crusher and out the dispenser chute. Replacing a worn or broken auger restores consistent dispensing and helps eliminate jams and grinding from a slipping spiral.

• Advances ice through the bin toward the crusher/dispenser chute
• Works with the crusher assembly to deliver cubed or crushed ice based on the selector
• A stripped or cracked auger may result in little/no ice dispensing while the motor runs
• Damage can cause ice jams, uneven dispensing, or grinding noises from the bin

• Unplug the refrigerator; remove and empty the ice bin, allowing any frost to thaw
• Wear cut-resistant gloves—crusher blades and sheet-metal edges are sharp
• Disassemble the crusher/blade stack and note the exact blade/spacer order
• Transfer the blade stack, bushings, and hardware to the new auger; reassemble and confirm smooth rotation before reinstalling

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

For complete assembly for easier installation order WP37001287