Lgh2b2867pf7a Parts

Change filter Read more

Front-wheel attaches to the shelf above. Where it screws in is kind of flimsy, no way to repair, had to replace the entire shelf, including the glass. Appliances Parts Pros had the best price, and it arrived quickly. You have to swap the metal brackets from the old to the new shelf (2 brackets x 5 screws), and reuse the old wheels as well. One thing to note, the holes for the screws and for the wheels are not threaded. The screws cut the threads. Use caution when putting in the screws and... Read more

• Ice maker dispenses too little ice

When I first searched the AppliancePartsPros.com site for my specific model, the ice maker that appeared in the parts list was not for my refrigerator. So, I bought one from one of your competitors. It arrived and worked but produced ice even more slowly than my original unit, albeit at 0F. So, I went back to AppliancePartsPros.com parts list and browsed completely through it only to find another ice maker that did match mine. It was almost twice the cost, but after installing it, worked... Read more

Unfortunately, this part isn't sold separately, but the plastic that is attached to the metal spring that allows the actuator to disengage broke and I had to physically pull the "paddle" part back up for the water to stop coming out. Easy removal with a square bit screwdriver. First, take off the trim piece underneath the LCD display (screws are underneath), then take out the screws for the LCD display and pull down and out, then unplug the wires. Then take the screws out of the actual part... Read more

• Marks left on clothes
• Noisy

The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more

Replaced the water filter base Read more

If you can't pull out the displacement pins on the crisper cover support clips that allow the wall to carry the weight of the cover, slides and drawer, you may need to push those pins in (they fall down the wall) to remove the clip. During the replacement of both front clips, I had one I could remove and one I had attempted to drill a tiny hole in to be able to pull the pin. Ultimately it did not work and needed to be simply pushed in. Do not worry, there is nothing below which the plastic... Read more

I ordered the replacement part. Your website was the only one I searched which exactly identified the correct part for me to order. The exploded diagram with numbered parts was very helpful. Read more

I believe we had two problems. Our gasket was ripped in several places and our drain pan line was clogged. Therefore the water was frozen and backing up into the freezer. Replacing the gasket is an easy job and could possibly be done quickly enough that you don’t have to remove your freezer food items if you don’t discover additional problems during the process. The most time-consuming part is the approximately 40 screws that hold the freezer door shelf panel and gasket to the door itself. ... Read more

My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

I ordered the plastic frames from Applianceparts.com. When they arrived I placed the unbroken glass within the frames. Very simple! Read more

Based on my model # and serial # the Appliance Parts Pros were able to quickly find and ship the gaskets I needed. The instructional videos showed me how to remove the old and replace with the new. I was able to easily do it myself. Read more

• Noisy

1. After hearing a loud noise on the freezer side of unit about halfway up, I started investigating what it could be? My conclusion was evaporator motor or evaporator fan blade. One of the signs of this issue was a distinct change in sound when I opened the freezer door. I ordered a new motor and blade, not knowing exactly what it was. 2. I couldn't get water to dispense, so I changed the filter and that wasn't the problem. I ordered a water valve and crossed my fingers. These parts arrived... Read more

• No heat or not enough heat
• Takes too long to dry

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more