Lgr3061bd Parts

Installed it by snapping it as video instructed. Read more

It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more

• Noisy

Looked up the part on AppliancesPartsPros.com. Ordered the part. Installed now it works like new. Read more

I put all pieces that I ordered on the dryer and plugged it in. Read more

• Door won't open or close

I replaced the hinge due to the hinge spring breaking. To replace the hinge you do the following: 1. Disconnect power to stove, either at circuit box or at outlet. 2. Lift door off of outside hinge arms ; no screws are used to attach the door to the hinge 3. Remove two screw on under side of cook top, one on each side. 4. Disconnect cook top connector. 5. Lift cook top off 6. Remove screws from top rail of stove that hold the side panel. 7. Remove the screw on the back that hold the side... Read more

I decided the problem was with the gas valve and I found the part on your web site. I ordered it and received the part in 3 days. I replaced the valve and the dryer works like new! This also gave me an opportunity to vacuum out the dust/lint that collects in and around the dryer. Read more

I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles. Read more

• Door won't open or close

The replacement hinge unit arrived in just two days. The JennAire (Maytag) oven door is fairly typical in that it easily lifts off of the hinge bars. Once the door is off then removing two screws is all that's required to remove the hinge unit from the oven. The new hinge slides up into place and while you hold it up inside of its location putting the old screws back in is very easy. After sliding the door back down onto the hinge bars the oven is as good as new Read more

Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine. Read more

I determined that it was a problem that occurred during the defrost cycle by resetting the GFCI outlet and forwarding the defrost timer until the defroster came on. Once the defrosting began, the GFCI outlet would reliably trip. I took apart the shielding inside of the freezer and tested the defrosting without the heating element or the thermostat connected. Since that looked good, I tested for proper functionality of the thermostat by removing it, placing it in a working freezer, and checking... Read more

I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros. Read more

I replaced all three baffles since the new one was a different design than then old one. i watched the video and the repair went well, except for hitting my hand with a hammer while removing the old baffles. went just like the video said it would Read more

I ordered the brioler pan for my new stove from y'all it was a little small but that's the part number in the book that I got with the stoveyall did a great job fast shipping just what I ordered will by from again thanks Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap... Read more

I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair... Read more