Lt7100xvno Parts

• Marks left on clothes

Maytag Gas Dryer Model: MGDE300VW1 I had previous experience with repairing my dryers, but this was a first for this model. Instructional videos very helpful. Ordered necessary parts and they were delivered with-in two days. Wow! Squeak found to be coming from idler pulley roller which no longer turned freely . The four other cabinet rollers had signs of wear. Dryer belt had frayed edges and a couple of burn spots in the belt from the motor turning before the drum did. Cleaned up all shafts... Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

• Will not tumble

I did a little research and found out that the dryer drum rollers needed to be replaced. I decided that since I would be replacing the 4 drum rollers that I should replace the belt and the belt drive pulley. This was a simple project thanks to YouTube. I used one of appliancepartspor videos to st me through the repair. Now I have a dryer that does not squeal like a pig! Read more

• Leaking

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more

• Noisy

Using appliancepartspros.com site took washer apart to diagnose bad clutch. The clutch was bad but once inside I noticed grease everywhere and after a quick online chat with rep. determined gear case was leaking and needed replacement. Replaced clutch & gear case. Followed video tutorial and took a little more than 30 minutes start to finish for me - I have no experience. The most difficult part for me was actually just getting the retainer ring (little wire) to secure clutch in place-took... Read more

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

I wanted to avoid pulling the drum. Luckily, my blower was easily accessed by pulling the front bottom panel. A couple of sheet metal screws were all I needed to remove the fan housing cover. I knew the fan was on reverse threads, i.e. righty-untighty. As it spins it tightens so no need for a retaining nut. I took off a screw holding on the exhaust tube and wiggled it out. I found the broken teeth inside. With the tube out of the way I was able to slide a crescent wrench in back and place... Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

• Burning smell

All's well that ends well, but the getting there was a bit of a pain. The web site suggests 3 possible causes for my problem (incl. the burning smell). I began with the first two since they were inexpensive compared to the motor, which was the third cause (and also the least often cause). There is no way to visibly tell if the motor is bad or not. After replacing the clutch assembly, which did have some plastic pins broken off) and the motor coupling (which actually looked fine, but the... Read more

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

• Leaking

In reality, this turned into a full-on rebuild project - with several parts orders, not just a simple repair. But I have to give credit: The parts listings with pictures on the AppliancePartsPros web site were really useful in figuring out what was going on inside the machine, and what parts I would need. Also: The repair videos were critical for me to be able to ensure I was reassembling everything correctly. Shout out to Simon, who was featured in several of the repair videos. His "gorgeous... Read more

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

I ordered what I thought were the necessary parts from appliancepartspro.com as my washing machine wouldn't spin. I should have watched there videos before I began as I took the whole cabinet off and everything and after receiving the parts and watching their video realized I didn't need to do so, at that point in time. When I put the pieces back together I found that the tub was really stuck, it would move but for the most part it was hard to move and creating a horrible noise. I knew I... Read more