Mavt466aww Parts

The Washer Tub to Pump Hose is an OEM part for Whirlpool washing machines. This hose connects the washer tub to the drain pump, facilitating the proper drainage of water from the tub during the wash and spin cycles.  

Causes of a bad tub to pump hose can include wear and tear from frequent use, blockages from lint or debris, and damage from overloading the washer or mishandling during maintenance.  

Symptoms of a bad tub to pump hose include:

• Leaks during the wash or spin cycles
• Water not draining properly from the washer
• Visible cracks, holes, or wear in the hose
• Unusual noises during the drain cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

Specs: 10-16 x 1/2 inch.

This factory replacement screw fastens the specified components in your appliance as shown in the parts diagram. It restores a secure fit and helps eliminate looseness, vibration, and noise when an original fastener is missing, stripped, or corroded.

• Secures panels, brackets, and assemblies at the locations designated for your model
• Direct replacement for the original fastener to maintain proper fit and alignment
• Replace when threads are damaged, head is rounded, or rust is present
• Common symptoms: loose or rattling parts, gaps/misalignment, increased vibration

• Disconnect power and shut off water supply if applicable before servicing
• Refer to your model's parts diagram for exact location and quantity
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug firmly but do not overtighten to prevent stripping

This flume hose kit replaces the flexible hose that routes water from the dispenser/fill flume into the washer tub. Restoring a tight, unobstructed hose helps prevent leaks and ensures detergents, bleach, and softener are carried into the wash.

• Directs fill/dispenser water from the flume to the tub during wash and rinse
• Restores proper flow so dispenser compartments empty correctly
• Helps prevent leaks caused by splits, brittleness, or loose connections
• Typical symptoms: water on the floor, dispenser not draining, weak flow into tub, musty odor near dispenser

• Disconnect power and shut off water supply before servicing
• Access the dispenser/flume area by removing the top or control panel per your model
• Note hose routing; transfer and secure clamps; avoid kinks and rub points
• Run a quick fill/rinse to check for leaks at both connections after installation

This lid switch actuator engages the washer's safety switch when the lid is closed so cycles can start and spin as designed. Replace a broken or missing actuator to restore proper lid switch engagement and reliable operation.

• Engages the lid switch when the lid is closed to enable agitation and spin
• A worn, cracked, or missing actuator can cause the washer not to start or to stop before spin
• Intermittent operation that changes when pressing on the lid often indicates misalignment
• Lack of an audible "click" from the lid switch can point to a faulty actuator or alignment

• Disconnect power before servicing; do not work on a live appliance
• Access the lid/switch area per your model's service procedure
• Remove the damaged actuator and install the new part, securing as designed
• Before reassembly, close the lid to ensure the switch clicks and engages properly

Color: gray. The back part of the knob measures about an inch in diameter, and the front part with the handle is about 2 inches in diameter.

This suspension spring hook connects a tub suspension spring to the washer frame, helping support and center the wash basket. Replacing a worn or missing hook can reduce shaking, banging, and off-balance interruptions during spin.

• Secures one end of a suspension spring to the cabinet/base
• Helps control tub movement and absorb vibration during agitation and spin
• Failure signs include excessive vibration or banging, tub leaning/sagging, or frequent out-of-balance stops

• Disconnect power and water; wear gloves and eye protection
• Access the suspension area per model; support the tub to relieve spring tension
• Use pliers or a spring tool to remove the old hook; note orientation and mounting location
• Seat the new hook fully and ensure the spring is engaged securely before reassembly and testing

This washer drain hose routes wastewater from the drain pump to your standpipe or laundry tub. Replacing a cracked or kinked hose restores reliable draining and helps prevent leaks during the spin/drain cycle.

• Connects the washer's drain outlet to the household standpipe or laundry tub
• Molded bend helps position the hose correctly and reduces kinking
• Typical symptoms: water leaking at the back or onto the floor while draining
• Visible splits, soft spots, brittleness, or abrasion on the hose
• Slow or incomplete draining caused by kinks or internal blockage

• Disconnect power and move the washer to access the rear; shutting off water is recommended as a precaution
• Place towels or a shallow pan to catch residual water when removing the old hose
• Transfer and reuse existing clamps/brackets if required; fully seat and secure connections, and route the hose to avoid kinks or rubbing
• Insert the outlet end properly into the standpipe or tub per your model's instructions, then run a quick drain/spin to check for leaks

This pressure switch hose carries air from the washer tub to the pressure switch so the machine can sense and control water level. Replacing a damaged hose restores proper fill control and prevents level-sensing errors. What it does:

• Channels air/vacuum from the tub to the pressure switch so the control can detect water level.
• A cracked, pinched, or collapsed hose may cause overfilling, underfilling, failure to advance cycles, or continuous fill.
• Restores accurate water-level sensing when replacing a worn or damaged hose.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove and replace the hose carefully; avoid kinks, sharp bends, or pinched routing that can impair sensing.
• Use the factory-style connection points and clamps; ensure both ends are seated securely.
• After installation, run a test fill or diagnostic cycle to confirm correct water-level operation and no leaks.

This small strainer sits inside the washer's water inlet valve and screens out sand, rust, and sediment from the supply lines. Replacing a clogged or missing screen restores normal fill flow and helps protect the valve.

• Filters debris from incoming hot and cold water before it reaches the valve and tub
• Helps maintain consistent water flow during the fill cycle
• A clogged or damaged screen can cause slow fill, very long fill times, or no fill
• Common causes for replacement include mineral buildup or rust/sediment from supply lines

• Unplug the washer and turn off both water supplies
• Place a towel or shallow pan, relieve hose pressure, and disconnect the fill hoses from the inlet valve
• Carefully pull out the old screen (needle-nose pliers work well); press the new screen fully and evenly into the valve port
• Reconnect hoses, restore water and power, and check for leaks
• Tip: Many washers have separate hot and cold inlets—inspect both screens and replace as needed

This washer tub mounting bolt secures the tub assembly to its support points. Replacing worn or missing hardware helps keep the tub aligned and stable through wash and spin, reducing vibration and noise. What it does:

• Anchors the tub assembly to its mounting bracket or frame
• Helps maintain alignment under load and during high-speed spin
• Replace if the bolt is stripped, rounded, rusted, or missing
• Symptoms can include excessive vibration/banging, tub shifting or scraping, and rattling hardware

• 1 mounting bolt

• Disconnect power and water before servicing; wear appropriate PPE
• Support the tub to relieve stress on the mounting points before removal
• Start threads by hand to avoid cross-threading; tighten bolts evenly across all mount points
• Do not overtighten; follow for torque guidance

Screw: 8-16 x 3/8 inch.

Drive motor isolator.

Size: 10-32

Motor plate isolator.