Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Plastic push-on pulley that mounts on the washer motor shaft to drive the belt. Replace if cracked, melted, worn, or no longer grips the shaft securely.
Acualy sounded and looked major but with a littel help with you tube the job only took 30 minutes. 3 bolts for the water pump pulley broken pulley poped off new one klick into place simple belt install good to go. Parts saved me $40 and where here in only 2 days. I couldnt be happyer. Read more
This factory replacement screw fastens the specified components in your appliance as shown in the parts diagram. It restores a secure fit and helps eliminate looseness, vibration, and noise when an original fastener is missing, stripped, or corroded.
Contacted the appliance parts pros, found the parts needed, watched the repair video and installed the parts Read more
This flume hose kit replaces the flexible hose that routes water from the dispenser/fill flume into the washer tub. Restoring a tight, unobstructed hose helps prevent leaks and ensures detergents, bleach, and softener are carried into the wash.
I figured it had to be the flume; changed the flume and hose, mounting screws Read more
This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.
I ordered the required parts from your website, the parts required were easily identified from the website tub blowup. The parts were delivered within 2 days and installed within 15 minutes Read more
Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.
I followed the Appliance Parts Pro's advice videos for the Maytag MAV6451AWW Atlantis washer on replacing the snubber ring and the suspension springs. Everything went just fine except replacing the two rear most suspension springs. None of the videos illustrated REINSTALLING the REAR springs which is extremely difficult because you can't get enough leverage with your arm extended. Observing my frustration, my wife recommended taking off the back side. You can't simply take off the back,... Read more
Washer won't start or spin? A broken lid switch actuator prevents the safety switch from engaging. This plastic striker restores proper operation in 5 minutes.
Replace the broken switch Read more
This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.
Removed old water valve and replaced it with new one. Reconnected wiring and water lines. Everything is working fine now. Read more
This washer drain hose routes wastewater from the drain pump to your standpipe or laundry tub. Replacing a cracked or kinked hose restores reliable draining and helps prevent leaks during the spin/drain cycle.
Bought a new hose and took one small cover off the back of machine, used pliers to remove clamp, took off old hose, put on new, replaced clamp, replaced cover and was done. Five minutes tops. Read more
Connects suspension spring to washer frame to support the tub. Replace if hook is broken, worn, or missing to restore proper tub suspension and alignment.
Fix washer overflowing or not stopping fill cycle. This water level pressure switch senses tub water and signals control to stop filling. DIY repair.
Filled tub to about 6 inches and inspected washer. Noticed that the tube leading from the air entrapment bubble on the exterior side of the drum had a small leak in it. Clipped off the part of the tube that had the hole in it(it was very close to the connector nipple) reconnected and problem was solved. Read more
This retaining ring secures a component on a shaft or within a groove so it stays aligned during operation. Replacing a bent, rusted, or missing ring helps stop wobble, noise, and parts working loose.
I took the machine apart and installed a new brake rotor , Brake stator and a snubber ring, after the install the machine works great and no more squeaking. I will say one thing about AppliancePartsPros.com that when I first received the order the brake rotor was new in the sealed bag but the brake material wasn't attached to it, customer service was helpful and sent me a new part the next day. I will use this company again. Read more
Drive motor isolator.
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
This washer tub mounting bolt secures the tub assembly to its support points. Replacing worn or missing hardware helps keep the tub aligned and stable through wash and spin, reducing vibration and noise. What it does:
Watched the video on how to replace. Ordered new roller, which was delivered in just a couple of days. Since the roller had broke, I was unable to roll out the refrigerator, so I tilted the refrigerator back and placed a small furniture slider under the roller frame to prevent gouging the wood floor. Then it was easy to slide out the refrigerator and replaced the roller as explained on the video. I had ordered a pin and bolt, just in case I would need to replace, but didn't need them. ... Read more
Motor plate isolator.
Hex head sheet metal screw secures appliance panels, brackets, and trim. Replace missing, stripped, or damaged screws to keep covers firmly attached.