Mbr2256k6s Parts

So this is a poor design in the first case. Not having a center support in the back almost guarantees a failure there eventually. I kludged together a support in my original more than a year ago, but finally the part broke too bad to limp along with anymore. This is the part I needed. That being said, be very attentive about the fact that it's not the entire shelf assembly. There is a metal support across the front of the frame that is not included. The trim above the drawers, and the... Read more

• Freezer section too warm

The fan has a very thin wire in it's coil, and when that wire breaks, you need a new fan. In a previous repair, i noticed that an ice build-up had dislodged the wiring on my fan and severed the coil winding. I was able to undo the winding a couple of turns and get it working again. But more recently, the fan stopped and there was no repairing it. So i ordered a new fan from AppliancePartsPros.com and it got here in very good time. The new fan was slightly different as the prongs seemed to be... Read more

1. Ordered new gasket. 2. Heated with blow dryer gasket until it resumed its normal shape. 3. Turned off refrig. 4. Cleaned freezer compartment. 5. Removed old gasket. 6. Installed new gasket. 7. Turned on refrig. 8, Operation back to normal in about 6 hours. Read more

• Fridge too warm
• Noisy

I determined that the motor that drives the damper valve that allows cold air into the refer was noisy. I ordered the replacement part from AppliancePartsPro.com. It arrived within 3 days and I changed the units out, which took about 10 minutes total. All is quiet with the refer now. Read more

• Freezer not defrosting
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

Pulled out storage bin Removed side track rail covers Popped off gear from holding clip Installed drive shaft Installed rail cover and storage bin Only took about 15 minutes Read more

Having never fixed a fridge before, I did a little research. The unit was not old & the cooling system was operating. Observing the frozen ice inside, I diagnosed it as the heat rod and/or it's thermostat as bad. I contacted ApplianceParts Pros, who assisted in confirming my theory. IMPORTANT NOTE: the sales advisor Joyce was truly an intelligent, knowledgable professional, NOT some "burger-order taker" usually encountered. This alone speaks VOLUMES. Subsequently, the parts arrived... Read more

Replaced the defrost thermostat and heater and the refrigerator was working again. Read more

Ordered part, the correct part came the next day. Read more

Looked up parts based on fridge model number, watched videos, and replaced parts using just a few tools... easy. Parts came quick, well packaged. After 16 years, plastic parts deteriorate and break. The fridge was operating fine, but the drawers and covers were failing. Much cheaper to replace a few parts ($$-$$$) than buy a new fridge ($$$$). The new parts matched up exactly to old ones. The videos were very helpful, but not perfect... for the Crisper Frame, there was a structural metal... Read more

Ordered and installed new ones. Read more

Ordered and installed new ones. Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

Ordered the new gasket from you - installed it and now my freezer is sealed i called to order the correct replacement and they were the very best at helping me !!!!! Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more