Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a dishwasher that won't heat water or dry dishes properly. This heating element restores hot water cycles and sanitization. Moderate DIY repair.
After reviewing the other repair stories related to this "7 blinking light" syndrome, I contacted their support staff via Chat. I relayed my symptoms along with model number of dishwasher. She indicated that this would normally mean an issue with either the heating element, the high limit thermostat, or the control board. Since the control board was so expensive and (luckily) out of stock, I ordered only the heating element and the thermostat. After pulling out the dishwasher and removing... Read more
Replaces a cracked, broken, or deteriorated dishwasher air inlet that allows fresh air into the tub during drying. Installs on the inner door panel.
The odor in the dishwasher was due to scum buildup in the walls, the racks, and in the lower part of the drain below the lower rotating arm. One of the valves in the vertical tube was stuck in the open position; since the valves cannot be replaced, the entire tube needed replacement. The check valve probably needed no replacement, but once I opened the bottom part, I decided to replace it anyway. I used this Youtube video to replace the tube, open and clean the drainage part of the washer: ... Read more
White retainer clip secures the kickplate at the bottom of your dishwasher. Replace if broken, cracked, missing, or lost to keep kickplate firmly attached.
Repair was easy. Just slotted the new parts in and they fit and worked fine, Read more
Replacement roller for dishwasher upper rack. Allows rack to glide smoothly in and out. Needed when roller is cracked, worn, or broken from regular use.
Slide diswasher out to reach the two screws that hold rollers. Reverse prcess, all done. Read more
Fix leaks around the dishwasher motor or poor spray pressure with this impeller and seal kit. DIY-friendly repair takes about 2 hours with basic tools.
My dishwasher quit cleaning dishes and lost all pressure. The food screen would keep clogging up and I would have to take it out and clean it by hand. After putting a new impeller in, the "gears" on the impeller connected with the screen blades, the old impeller the "gears" were stripped off. And the new impeller comes with new seals, after taking old one out I noticed it wasn't long before my old seals would have started leaking. Very simple repair if you watch the great video that... Read more
Covers the lower front of your dishwasher for a finished look. Replace if cracked, broken, missing, or damaged from impact or wear and tear.
Had my kitchen renovated and my contractor lost the access panel for my Whirlpool dishwasher so I had to find a replacement. Found what I was looking for at AppliancePartsPros.com, chatted with a sales customer service rep to make sure it was the correct part. Ordered it, paid for standard shipping, which said 2-3 days, it arrived at my house the next day! The part was also a genuine Whirlpool replacement part, not a generic part that "should" fit, needless to say, it fit perfectly and... Read more
The Upper Dishrack Rail is an OEM replacement part for Whirlpool dishwashers. It guides upper racks in and out for easy access to dishes.
Causes of faulty rails can include worn rollers, broken clips, or stress cracks in modules after repeated cycles.
Symptoms of a bad upper dishrack rail include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Ordered the parts and followed the instruction videos that Sears provide, Initially tried to order parts from Sears directly but the web-page kept complaining about my shipping address. Their loss- no wonder they're going out of business. Also, should note that the original assembly was plastic but the replacement was metal. Sure sign of a crappy cost-cutting decision. Overall, very happy with Appliance Parts Pros! Read more
Fix standing water in your dishwasher bottom with a check valve replacement. Prevents backflow and improves cleaning. DIY repair in 30-60 minutes.
The Filter Assembly is an OEM part for Whirlpool dishwashers. This component is responsible for trapping food particles and debris, preventing them from recirculating during the wash cycle and ensuring that dishes come out clean.
Causes of a bad filter assembly can include accumulated debris, regular wear from repeated use, or damage from harsh cleaning agents. A compromised filter can reduce the dishwasher’s cleaning performance and lead to buildup inside the machine.
Symptoms of a bad filter assembly include:
Replaced filter. It works great now, no more brown spots. Read more
Fix a dishwasher not filling with water by replacing the water level float lever. This lever regulates water levels and prevents leaks. Easy 15-minute DIY repair.
Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more
Seals the dishwasher air vent to prevent water leaks during operation. Replace if you notice dripping under the vent or wet insulation behind the panel.
First tried replacing the seal around the door as that was the simple and most logical fix. Still leaked. Removed the front and upper panel to inspect. Found calcium deposit running down from under the Air Vent Assembly and wet behind the black stick-on insulation. Easy to trace the leak to the bottom of the door. => Ordered new Air Vent Assembly, gasket and Vent Deflector. Parts arrived. Took 5 minutes to remove upper panel. Removed the two wires from the Air Vent Assembly. Inserted a... Read more
The water supply manifold distributes incoming water to various dishwasher components and is typically located at the bottom of the unit. Replace when experiencing water leaks, poor spray pressure, or uneven water distribution.
Easy fix. simple assembly Read more
Bracket that secures the water level switch in your dishwasher. Replace if cracked, broken, or damaged, causing the switch to shift out of position.
The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.
Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
We ordered parts from appliance parts pros and I fixed it. Read more
Supports and secures the upper spray arm in your dishwasher. Replace if cracked, broken, or detached. Clips to the bottom of the upper rack.
Note: This manifold has two holes on the part that mounts to the back wall of the dishwasher. For one hole use WPW10571949.
I discovered that the manifold was not connecting with the water supply,so the dishes in the upper tray were not being washed. This was caused because the rear hanger on the manifold had broken and it did not lineup properly into the water supply connection in the back of the dishwasher. I removed the manifold and found that it had two part numbers stamped on it. I searched on both part numbers and received a hit on the second part number. The photo looked exactly like my manifold so I... Read more
Replaces cracked, mineral-clogged, or punctured feed tube that routes water from lower manifold to upper spray arm. Includes rubber grommets and fittings.
I replaced the rear tube that feeds water to the top and middle spinners, and this appears to have fixed the problem. The middle spinner, which is attached to the bottom of the top rack, has a tube that connects to a hole in the middle of the rear tube.This hole has a rubber flap and I noticed that this flap was wide open. The tube under the tray has a straight edge protruding from it at the back. This edge pushes the flap open and I suspect that when the water is flowing, this edge rotates... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.