Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Door won't latch or stay closed? This dishwasher door latch assembly fixes latching failures and prevents mid-cycle stops. Moderate DIY repair with video.
I ordered the Maytag Latch-Door mechanism and was able to get a service manual from appliancepartspros.com. I followed instructions, disconnected power FIRST, and removed the inner door panel screws and the inner and outer doors came apart. I was then able to disconnect the power leads to the electronic latch door mechanism and remove the whole assembly. The assembly was loosely attached to the inside of the outer door by plastic posts and squeeze levers. I compared the OEM part with the... Read more
Dishwasher won't start or lights flash? The door switch signals the control board when closed. Easy DIY fix with video guide. Restore operation.
This was a difficult problem to diagnose. Because the machine would start the wash cycle then shut down after a few minutes of running, it appeared that the cause might be a bad thermostat or heating element, but all checked out ok. That led me to believe that the control panel may be the culprit but it also appeared to be working correctly when I ran the diagnostics program. A visual examination of the components found that the door switch electrical connections looked discolored, so I removed... Read more
Fix a dishwasher that won't heat water or dry dishes properly. This heating element restores hot water cycles and sanitization. Moderate DIY repair.
After reviewing the other repair stories related to this "7 blinking light" syndrome, I contacted their support staff via Chat. I relayed my symptoms along with model number of dishwasher. She indicated that this would normally mean an issue with either the heating element, the high limit thermostat, or the control board. Since the control board was so expensive and (luckily) out of stock, I ordered only the heating element and the thermostat. After pulling out the dishwasher and removing... Read more
Replaces a cracked, broken, or deteriorated dishwasher air inlet that allows fresh air into the tub during drying. Installs on the inner door panel.
The odor in the dishwasher was due to scum buildup in the walls, the racks, and in the lower part of the drain below the lower rotating arm. One of the valves in the vertical tube was stuck in the open position; since the valves cannot be replaced, the entire tube needed replacement. The check valve probably needed no replacement, but once I opened the bottom part, I decided to replace it anyway. I used this Youtube video to replace the tube, open and clean the drainage part of the washer: ... Read more
Replacement roller for dishwasher upper rack. Allows rack to glide smoothly in and out. Needed when roller is cracked, worn, or broken from regular use.
Slide diswasher out to reach the two screws that hold rollers. Reverse prcess, all done. Read more
White retainer clip secures the kickplate at the bottom of your dishwasher. Replace if broken, cracked, missing, or lost to keep kickplate firmly attached.
Repair was easy. Just slotted the new parts in and they fit and worked fine, Read more
Fix leaks around the dishwasher motor or poor spray pressure with this impeller and seal kit. DIY-friendly repair takes about 2 hours with basic tools.
My dishwasher quit cleaning dishes and lost all pressure. The food screen would keep clogging up and I would have to take it out and clean it by hand. After putting a new impeller in, the "gears" on the impeller connected with the screen blades, the old impeller the "gears" were stripped off. And the new impeller comes with new seals, after taking old one out I noticed it wasn't long before my old seals would have started leaking. Very simple repair if you watch the great video that... Read more
The Upper Dishrack Rail is an OEM replacement part for Whirlpool dishwashers. It guides upper racks in and out for easy access to dishes.
Causes of faulty rails can include worn rollers, broken clips, or stress cracks in modules after repeated cycles.
Symptoms of a bad upper dishrack rail include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Ordered the parts and followed the instruction videos that Sears provide, Initially tried to order parts from Sears directly but the web-page kept complaining about my shipping address. Their loss- no wonder they're going out of business. Also, should note that the original assembly was plastic but the replacement was metal. Sure sign of a crappy cost-cutting decision. Overall, very happy with Appliance Parts Pros! Read more
Fix standing water in your dishwasher bottom with a check valve replacement. Prevents backflow and improves cleaning. DIY repair in 30-60 minutes.
The Filter Assembly is an OEM part for Whirlpool dishwashers. This component is responsible for trapping food particles and debris, preventing them from recirculating during the wash cycle and ensuring that dishes come out clean.
Causes of a bad filter assembly can include accumulated debris, regular wear from repeated use, or damage from harsh cleaning agents. A compromised filter can reduce the dishwasher’s cleaning performance and lead to buildup inside the machine.
Symptoms of a bad filter assembly include:
Replaced filter. It works great now, no more brown spots. Read more
Seals the dishwasher air vent to prevent water leaks during operation. Replace if you notice dripping under the vent or wet insulation behind the panel.
First tried replacing the seal around the door as that was the simple and most logical fix. Still leaked. Removed the front and upper panel to inspect. Found calcium deposit running down from under the Air Vent Assembly and wet behind the black stick-on insulation. Easy to trace the leak to the bottom of the door. => Ordered new Air Vent Assembly, gasket and Vent Deflector. Parts arrived. Took 5 minutes to remove upper panel. Removed the two wires from the Air Vent Assembly. Inserted a... Read more
The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.
Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
We ordered parts from appliance parts pros and I fixed it. Read more
Dishrack wheel assembly for dishwashers. Replaces broken, cracked, or worn wheels that prevent smooth rack sliding. Includes wheel and axle bracket.
Tipped the dishwasher on to its front, loosened the drain hose clamp and pulled the hose off. Then unscrew the fill hose which looks like a garden hose adapter. Cut the zip tie on the drain hose and take note of how both hoses are routed, then pull both hoses out the back of the dishwasher. Insert new hoses and route them correctly and hook everything back up. Couple of notes, I didn't have to take off the outer cabinet to do this repair. Get plenty of towels because a lot of water can get... Read more
Side mounting bracket kit secures your dishwasher to adjacent cabinetry. Replace missing, damaged, or broken brackets for stable installation.
I haven't yet started to place the dishwasher in place is Read more
Seals the water inlet connection to prevent leaks where water enters the dishwasher tub. Replace if you notice moisture damage or leaking at the valve inlet.
Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more
The Nut is an OEM part for Whirlpool dishwashers. This nut secures the float switch, a key component in regulating the water level within the dishwasher. The float switch ensures your dishwasher does not overfill by triggering the water to stop once it reaches a certain level.
Over time and with regular use, the nut that holds the float switch in place can become loose or damaged. This could potentially allow water to seep through gaps, leading to leaks, or could cause the float switch to malfunction, affecting the dishwasher's ability to regulate water levels accurately.
Symptoms of a faulty Nut include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.