Mdbh 969Fwb1 Parts

Located between the console and door

Includes two screws, two clamps, and undercounter mounting brackets.

Lower wash arm redirects pressurized water across the dishwasher's lower rack to rinse and remove food and residue, restoring intended wash coverage and improving cleaning performance. What it does:

• Directs jets of water through multiple spray holes to rinse dishes on the lower rack.
• Helps remove stuck-on food, film and spotting on plates, bowls and cookware.
• Replaces cracked, clogged or broken lower spray arms that can cause poor cleaning or leftover residue.
• Works with the dishwasher's pump flow to maintain proper spray pattern across the lower rack.

• Refer to your model's parts diagram and instructions; the arm commonly snaps or threads onto the lower spray arm mount and procedures vary by model.
• Always disconnect power to the dishwasher before servicing; follow basic safety precautions.
• Clean the filter and any debris from spray holes before installing to avoid re-clogging.
• Inspect the mounting clip or retaining nut when removing the old arm and replace if damaged.

This active vent assembly controls airflow from the dishwasher during and after a cycle, releasing humid air at the right time for better drying. Replacing a faulty vent can reduce lingering moisture and steam escaping from the door.

• Regulates and directs moist air out of the tub during the dry portion of the cycle
• Closes during wash to help contain water and heat inside the dishwasher
• Helps reduce interior condensation and improve overall drying results
• Common failure symptoms: dishes not drying, moisture remaining after the cycle, steam escaping at the top of the door, or unusual noise from the vent area

• Disconnect power at the breaker before servicing; allow the unit to cool
• Access is typically through the inner door panel; retain and reuse mounting hardware as required
• Inspect and correctly seat the vent seal to prevent steam leaks
• After installation, run a test cycle to check for proper vent operation and sealing

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

Replacement fill hose that routes water from the household supply to the appliance's ice maker and water dispenser, restoring proper water delivery and helping prevent leaks or pooling from a damaged line. What it does

• Directs water from the inlet valve to the ice maker and dispenser for ice production and dispensing.
• Maintains steady water flow; prevents kinks and pinched lines that reduce flow.
• Replace if cracked, split, collapsed, or leaking.
• Common symptoms: reduced or no water to the dispenser or ice maker, visible leaks, or pooling under/behind the appliance.

• Turn off the water supply and disconnect power before servicing to avoid flooding and electrical hazard.
• Inspect and replace clamps or fittings as needed; ensure proper seating and a snug, leak-free connection without overtightening.
• Check for kinks in the hose and route it so it won't be pinched by the appliance or cabinetry.
• After installation, turn the water back on and test for leaks at all connections.

This dishwasher overfill control float mounts in the tub floor and rises with the water level to trip the float switch and stop filling. Replacing a warped or stuck float restores proper fill control and helps prevent leaks. What it does:

• Monitors tub water level and actuates the float switch to shut off the inlet valve
• Helps prevent overfilling and water leaking from the door
• Common symptoms of a faulty float include no fill, continuous filling/overfilling, or inconsistent water level

• Float and retainer

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; lift out the old float
• Access beneath the tub may be required to release/install the retainer
• Ensure the float stem engages the switch lever and moves freely; test-fill and check for leaks

This foam pad installs between the inner and outer door panels of a dishwasher to dampen sound and help shield the outer panel from heat and moisture, keeping operation quieter and the door better protected. What it does:

• Lines the inside of the outer door panel to reduce operating noise and vibration
• Acts as a thermal and moisture barrier for the outer door panel
• Helps maintain proper door performance when the original insulation is worn or missing
• Replace if torn, degraded, or waterlogged, or if noise/condensation around the door has increased

• 1 door insulation pad

• Disconnect power and shut off water to the dishwasher before servicing
• Support the door; remove perimeter screws to separate the inner and outer door panels
• Note the pad's orientation; seat the new insulation evenly without pinching wires or harnesses
• Reassemble panels and fasteners; verify smooth door/latch operation

This silverware basket organizes utensils in the lower rack of your dishwasher so water can reach them evenly. Replacing a cracked or missing basket keeps small items contained and helps prevent interference with the spray arm.

• Holds cutlery and small utensils upright during wash and rinse cycles
• Keeps small items from falling through the rack or onto the heater
• Replace if the basket is cracked, warped, melted, or missing sections
• May help with utensils tipping over, rattling, or blocking the spray arm

• Remove the lower rack, lift out the old basket, and position the new basket in the same location
• Ensure the basket does not obstruct the spray arm and the rack rolls freely
• Handle sharp utensil tips carefully; install with the dishwasher cool and empty

Used on the upper dishwasher dishrack.

This dishwasher door strike mounts to the tub opening and provides the catch point for the door latch. Replacing a worn or bent strike restores positive latching so the control can sense a closed door and run cycles reliably.

• Provides the catch the door latch locks onto
• Engages the door switch so the dishwasher can start
• Helps keep the door securely closed during operation
• Common symptoms: door won't latch or pops open; unit won't start unless pressure is applied to the door; strike is visibly bent, worn, or missing

• Disconnect power at the breaker; turn off water if you need to move the appliance
• Open the door to access the strike at the tub opening; remove mounting screws, replace the strike, and tighten securely
• Save and reuse the original mounting screws
• After installation, check latch engagement and adjust appliance leveling or alignment if needed

This upper rack wheel and axle assembly lets your dishwasher's top rack glide smoothly and stay level. Replace a cracked or missing wheel to fix hard-to-slide racks, scraping noises, or a rack that slips off the rail.

• Provides rolling support for the upper rack along the rails
• Helps keep the rack aligned to prevent sagging or derailment
• Replaces worn, cracked, or seized wheel assemblies
• Common symptoms: rack hard to slide, wheel wobbles/missing, grinding or scraping sounds, rack coming off track

• Disconnect power to the dishwasher for safety
• Pull out the upper rack and remove the rail end caps if needed
• Release and remove the damaged wheel/axle assembly from the rack
• Snap the new assembly into place, reinstall end caps, and test rack movement

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:

• Fastens and secures panels, brackets, trim, or internal components as specified for your model
• Replaces missing, corroded, or stripped hardware to restore a proper fit
• Helps prevent vibration, rattling, and misalignment caused by loose fasteners
• Addresses issues like a loose panel/handle or a screw head that's rounded off

• 1 screw

• Disconnect power; if applicable, shut off gas and water before servicing
• Use the correct driver size; start by hand to avoid cross-threading
• Tighten snugly—do not overtighten into plastic or thin sheet metal
• Keep track of original screw locations and lengths during reassembly

This Drain Pump Motor Assembly replaces the washer's drain pump motor and impeller so the machine can move water out during drain and spin cycles. Restores proper draining and reduces standing water in the tub. What it does:

• Pumps water from the tub during drain and spin cycles to help clear wash water.
• Replaces a failed or noisy pump motor that hums but won't drain.
• Stops or reduces standing water and slow-drain symptoms.
• Helps address leaks or visible damage at the pump housing or impeller.

• Disconnect power and turn off water supply before starting any repair.
• Remove the washer access panel and drain remaining water from the tub before replacing the pump.
• Note wiring and hose locations during removal; reconnect hoses and electrical plug securely.

This little door seal goes on the corner of the dishwasher door. There are two of these seals - one in each corner. It is recommended to order and replace both. If you need pushnuts, order 99002756.