Med6100dc0 Parts

This is the washer's main electronic control. As the central control unit, it manages power and communication to key components so cycles start, run, and finish correctly—restoring reliable operation when the original board fails.

• Controls overall cycle timing and option execution
• Distributes power/signals to the water inlet valves, drive motor, drain pump, door lock, and user interface
• Common failure symptoms: won't power on or start, won't advance/complete cycles, unresponsive or intermittent controls

• Disconnect power before service and follow all safety precautions
• Handle the board by the edges and use ESD protection
• Photograph/label wire harnesses; seat all connectors fully and secure routing
• After installation, run the appliance's diagnostic/test cycle to verify operation

10 - 16 x 1/2

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This broken belt switch is a dryer safety switch that senses drive belt tension and opens the motor circuit if the belt breaks or slips off. Replacing a failed switch can resolve a no-start or no-tumble condition. What it does:

• Monitors drive belt tension via the idler assembly
• Interrupts power to the motor when the belt is broken or not tensioned
• Helps prevent heating without airflow when the belt has failed
• Symptoms can include: dryer won't start, drum won't turn, or the dryer stops as soon as the Start button is released

• 1 switch

• Disconnect power; for gas models, shut off the gas supply
• Access the switch near the idler pulley by removing the lower/front panel per your model
• Transfer wires from the old switch to the new one; mount securely with the actuator aligned to the idler arm
• Run a brief test cycle

Specs: 10-16 x 1/2 inch.

This Dryer Drying Rack creates a stationary shelf inside the drum so items that shouldn't tumble—like shoes, sweaters, and hats—can dry gently. Replace a missing or damaged rack to restore safe, non-tumble drying capability.

• Provides a stable platform inside the dryer for items that need to stay still while drying
• Helps reduce wear, scuffing, and noise from tumbling delicate or bulky items
• Restores function when the original rack is cracked, warped, or missing
• Common symptoms: rack won't seat/lock, sits unevenly, or items won't stay on the rack

• Disconnect power before installing
• Open the door and seat the rack so the rear support engages the back ledge/slots and the front rests on the door opening
• Ensure the rack is secure and clear of the rotating drum; load items evenly
• Remove the rack before returning to normal tumble cycles

The Whirlpool Dryer Door Catch is an OEM part for Whirlpool dryers. It secures the dryer door closed during operation, ensuring the safety and proper functioning of the appliance. This component engages with the door latch to hold the door shut, allowing the dryer to operate without interruption.

Causes of a bad dryer door catch can include normal wear and tear from frequent use, accidental damage, or deformation of the catch or latch that prevents proper engagement. Over time, the door catch can become loose or break, necessitating replacement to maintain the dryer's performance and safety.

Symptoms of a bad dryer door catch include:

• The dryer door not staying closed during cycles
• Difficulty closing the door securely
• The dryer stopping mid-cycle due to the door opening

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This belt restrainer is the small guide that keeps the dryer's drive belt on the motor pulley. It prevents the belt from walking off during operation, supporting consistent drum rotation and reducing premature belt wear. What it does:

• Guides and retains the drive belt on the motor pulley
• Helps maintain proper belt tracking with the idler assembly
• Can help with symptoms like drum not turning, belt repeatedly slipping off, burning rubber smell, or frayed belt edges

• 1 belt restrainer

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the motor area per your model (remove front or lower access panel)
• Position the restrainer adjacent to the motor pulley with slight clearance to the belt; route the belt correctly around drum, idler, and motor
• Hand-rotate the drum to confirm alignment before reassembly and testing

This door catch assembly secures the door by engaging the mating latch or strike, keeping it firmly closed for proper operation and safety. Replace a worn or broken catch to restore reliable door closure and consistent performance. What it does

• Engages the door latch/strike to hold the door closed during use
• Helps maintain proper door alignment and contact with seals/interlocks
• Restores a positive latch feel and consistent closure
• Common signs of wear: door won't latch or pops open, must be slammed to close, visible damage to catch tabs

• One door catch assembly

• Unplug the appliance or switch off power at the breaker before servicing; for gas appliances, shut off the gas supply
• Open the door, access the catch at the cabinet/frame, and remove retaining screws or clips
• Transfer any reusable hardware from the original part and install the new catch
• Verify smooth latch engagement and door alignment before restoring power

This lens covers and diffuses an appliance light source, protecting it from heat, grease, and moisture while delivering even illumination. Replacing a cracked or yellowed cover restores brightness and a clean, finished look.

• Shields the bulb or LED from debris, grease, and impact
• Diffuses light for more even, glare-free illumination
• Helps maintain the appearance of the light area
• Common symptoms: cracked, broken, missing, discolored, or loose lens

• Disconnect power and let the lamp/surface cool before servicing
• Support the old lens while removing any retaining screws or clips
• Align tabs or holes carefully; seat the new lens fully and evenly
• Do not overtighten fasteners to avoid cracking the lens

This drying rack sits inside the dryer drum to hold items stationary for tumble-free drying. It's ideal for shoes, sweaters, and other delicate pieces that need air circulation without bouncing or spinning, helping prevent damage and excess noise. What it does:

• Provides a stable surface for no-tumble drying inside the drum
• Helps prevent scuffs, stretching, and wear on delicate items and footwear
• Replaces a missing, cracked, or warped rack
• Common signs you need a new rack: won't seat securely, bent or broken frame, or persistent rattling when in use

• 1 drying rack

• Unplug the dryer and allow the drum to cool before placing the rack
• Open the door and position the rack per your owner's manual so it sits level and secure
• Load items evenly; ensure nothing contacts the rotating drum
• Use only the rack-dry/low-heat/air cycles recommended for your model; remove the rack before normal tumbling cycles

Side and bottom exhaust kit.

STACK KIT FOR LONG VENT DRYER

This is a genuine OEM drive motor with dryers.This drive motor is critical for the dryer to function as intended, and if the motor is broken or malfunctioning, the user may notice that the drum is unable to spin. This is because the drive motor is responsible for driving the belt that rotates the drum. The user should check for a blown thermal fuse in electric dryers before replacing the entire drive motor. The appliance will need to be completely disconnected from all power sources before repairs are undergone and work gloves should be worn to prevent injury.This part has been made by Whirlpool and sourced directly from the manufacturer. It is sold individually. This door is manufactured from high-quality, durable, non-corrosive materials. It is an authentic replacement part and thus is compatible with dryers manufactured by various brands, including Whirlpool, Maytag, Jenn-air, and Amana.

This leveling leg threads into the base of the appliance to set height and keep it stable. Replacing a worn or missing leg helps eliminate rocking and vibration for quieter, smoother operation and proper alignment. What it does:

• Threads into the base to adjust height and level the appliance
• Stabilizes the cabinet to reduce rocking, vibration, and noise
• Helps maintain proper door alignment and smooth operation
• Replaces stripped, damaged, or missing leveling hardware

• 1 leveling leg

• Disconnect power; shut off water or gas supply if applicable
• Protect floors and use assistance to safely tip or lift the appliance
• Remove the old leg; thread the new leg by hand to avoid cross-threading, then adjust to level
• Ensure all legs contact the floor and the unit is stable after positioning

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.