Mfi2269vemo Parts

We turned off the circuit breaker. We then removed the light cover and then the control panel. We disconnected the Keyboard, Utah, plugged in the new one and turned the breaker on to see if everything worked. We realized that we did not need a new jazz board so that is being returned. The old Keyboard was removed, the new one attached and all the parts were put back. The frig works fine now at the recommended settings of zero and 38F. Read more

I had a slow leak at the water inlet valve where the water line from the filter assembly connected to the water inlet valve. I determine that the water line had scratches in it which caused it to not seal. Had to buy the entire reservoir and filter assembly to get that water line. The replacement was smooth. It took about 30 minutes to swap out and it fixed the leak. Read more

So this is a poor design in the first case. Not having a center support in the back almost guarantees a failure there eventually. I kludged together a support in my original more than a year ago, but finally the part broke too bad to limp along with anymore. This is the part I needed. That being said, be very attentive about the fact that it's not the entire shelf assembly. There is a metal support across the front of the frame that is not included. The trim above the drawers, and the... Read more

I ordered a new solenoid valve set and watched the online video of the replacement process. So after emptying my freezer and fridge, removing the doors and freezer drawer, so I could mover the fridge out of its cove, I discovered after taking the panels off the rear, that my fridge is different than that shown in the video. I went back online and discovered in one of the exploded views of the cabinet there is a panel inside the refrigerator which can be removed after taking the shelves out of... Read more

Pulled out storage bin Removed side track rail covers Popped off gear from holding clip Installed drive shaft Installed rail cover and storage bin Only took about 15 minutes Read more

The manual had instructions for pulling things apart, the flaps over the drawer tops and the clear plastic inserts in the shelf. Flaps--Easiest to work with when the shelf is out and upside down. Slide flaps to the side a little to release the axle pin on the flaps from the receptacle hole on the shelf frame. Clear plastic plates are held in with a plastic pin on the side of the shelf frame. Carefully pull the side off the shelf there away from the pin slot until the insert pops out.... Read more

Replaced relay and capacitor attached to compressor Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

A relay in my refrigerator would periodically click off, causing the compressor motor to stop and the LEDs on the front panel to turn off. This became more frequent until it finally "blanked out" permanently. No cooling, no lights on the front panel, no water or ice, only the inside lights worked. Isolating the problem to the control board was easy, and replacing the control board was very easy thanks to the videos and previous customer reports available here. After installing the board, I... Read more

Touch up paint Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

Although I only needed to replace the drawer support (end cap) on the right side the kit comes with replacements for both sides. I was surprised to see that the air flow adjustment mechanism that is located on the right side end cap was not included. I should mention that I did not disassemble the drawer mechanisms before ordering the end cap(s). The kit contained only the two molded end caps - no fasteners, mechanisms, or anything else. It turns out that this was all perfectly fine. The... Read more

Replaced It With New One Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

The dual inlet valve was the problem. The hardest part of the repair was moving the refrigerator so we could unplug it. The whole job took about 25 minutes and that includes the time we spent emptying and reorganizing the shelves. I love AppliancePartsPros.com. We have used this website to fix our oven, washer, dryer and now the ice maker. Thank you AppliancePartsPros! We only used one screwdriver and that was only used to open the back panel of the refrigerator. Read more