We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Spin Bearing Washer is an OEM part for Frigidaire washing machines. Situated inside the transmission housing, this thin metal washer acts as a subsurface support for the belt pulley bearing. The spin-bearing washer facilitates smooth, balanced rotation essential for agitated and spun wash cycles. Causes of a bad spin-bearing washer include wear and fatigue from years of successive rotations, potentially allowing excessive movement between housing components. Symptoms of a bad spin-bearing washer involve:
This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more
Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.
This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more
Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.
My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more
This is a small metal grounding ball that sits in the rear drum bearing area of the dryer. It helps dissipate static electricity buildup in the drum during operation. Replace this part if you are experiencing excessive static cling on clothes, static shocks when unloading laundry, or if the original ball is missing or worn.
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros. Read more
The Ignitor Assembly is an OEM replacement part for Frigidaire dryers. It serves as the ignition source safely firing up burners to initiate drying cycles.
Causes usually relate to the continual thermal shock experienced from heating and then rapidly cooling over extended use. As a foundational safeguard, ignitors require OEM replacement when arcing declines.
Symptoms of a faulty ignitor can include:
This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.
The blower wheel center was worn down and spinning freely on shaft. Removing front covers, controls and brackets gave access to blower, which front half came off removing screws. (One screw underneath bracket) Pushed new blower on. (It's keyed and has small tabs that line up with groove on shaft). Installed clamp, reassembled and tested. Don't forget to pull the plug out before working on any appliance. Read more
For a complete drum bearing and shaft kit order 5303281153.
Adjustable leveling leg that screws into the washer cabinet to stabilize and level your appliance. Replace if broken, damaged, or missing to prevent rocking.
After watching YouTube videos on possible cause, went to appliancepartspros and order seal and leveling legs since the had been missing since machne was given to us. Parts came in within the week and replaced . No more leaks!! Read more
Washer motor won't start or stops mid-cycle? This motor start capacitor stores electrical energy to start your washer motor. Moderate DIY repair.
I found your site which was most helpful. I saw on your forum, that others had replaced a motor & capacitor with + results. I was willing to spend what I thought was a reasonable amount & your guarantee was the clincher. I knew that if I called the appliance store where we had purchased the washer in 1998, it would be very expensive & even more important, it would take many days as they would have to order the part & then schedule a service call. I installed the motor & capacitor & was... Read more
This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:
This was more maintenance than a fix. I replaced the door gasket and temp sensor on my dryer. Thought what the heck and it might work more efficiently. I also replaced the shocks on my front loading washer. That was a bit of a chore, but could not have done it without the video that showed how to replace them. The socket was the life saver. All is working just fine. Who knows maybe I'll get another 20 year out of them. Read more
Includes motor, motor pulley and housing. Motor pulley no longer available separate
I replaced the motor. It was time consuming because you have to take all of the parts that attach off. Was fairy simple. Pleased about the parts delivery. Ordered and received the next day. Read more
White door handle for laundry center dryer door. Replaces cracked, loose, or missing handles. Restores secure grip for opening and closing the door.
Ordered a new handle from appliancepartspros.com and installed. Read more
Fix a washer that won't drain or makes whining sounds with this pump and motor assembly. Common causes: debris lodged in pump or burned-out motor.
When I removed a bunch of very wet soaking towels at the end of a wash cycle, it was clear that the water was not draining properly. The washer also made a very loud noise during the water drain period. That was suspicious. I ordered the part, opened the washer, removed the old pump and faced with a nasty surprise. You may laugh at this, but there was a toothpick in the old drain pump! most of it was still there, and it seemed like the toothpick was stuck in the pump in such a position that it... Read more
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
Fix a dryer that won't turn off or advance through cycles with a new timer. Controls cycle duration and automatic shutoff. Moderate DIY repair.
I ordered a new dryer timer. Read more