Mmv4203bd00 Parts

Bought a new home with microwave venting into kitchen. Ordered damper assembly needed to vent through the wall to the outside. Removed microwave, followed directions in original installation instructions, turned fan over, cut hole in wall, installed wall cap and replaced oven. Problem solved. Read more

Watched a You tube video, showed how to remove bottom, unhook wiring, then proceed to top case. Once removed, case is turned upside down so the capture nut can be installed. Part fit perfectly and BAM, done. Case refitted and finished. Part arrived in 2 days. Great service. Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

• No heat

After dismounting the unit from its wall-hanging bracket, the most tedious part of the repair was removing over a dozen screws holding the cover in place from the top, bottom, and both sides. Fortunately, I had placed the unit on a bench that allowed me to slide the unit allowing access to the screws on the bottom edges of the unit. Always discharge the capacitor before continuing to work on the unit by discharging the capacitor by shorting the contact without the diode to ground. Access to the... Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

Well, I gotta say I was happy to find you still had parts for almost 20 year old microwaves. The microwave itself worked fine, so I hated to have to buy a new one, but I just couldn't take being hit in the head anymore; and my fix of using string and wire to tie it to the surrounding cabinets was unsightly to say the least. I'm glad I did some research and found this part - all I had to do was pop it in place and now the vent grill is secure. Problem solved with minimal cost. Read more

Checked switch with a voltmeter, determined the switch was bad. Ordered a new switch....watched a short how to you-tube video.....and from there.....it was fixed. Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

• No heat

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

Replaced with new grill-vent.perfect fit. Used same screws. Read more

When the new bulb didn't want to go in, I felt around and realized the base of the old bulb was still in there. With some effort I got it out and new bulb in, Light cover fit fine, but did not come with a screw to hold it in. That would have been helpful. Read more

• Won't start

Watched u-tube Read more

• No heat

Utilized a YouTube video to isolate the door switches as the issue. These were easily identified following the isolation process and simple testing. I ordered a door switch and secondary switch on Monday and they arrived on Tuesday via FedEx. 15 Minutes to re-install, re-assemble cover and the unit was working fine. A very good experience with parts availability and shipping. Read more