Mvwc565f20 Parts

This replacement hose routes liquid or air between internal components, maintaining a secure, leak-resistant path. Replace a brittle, cracked, or clogged hose to prevent leaks and restore proper flow and sensing performance.

• Provides a sealed pathway between components such as the pump, tub, valve, drain path, or pressure system
• Helps maintain correct water flow or pressure/level sensing
• Common symptoms: leaks, kinks/cracks, standing water, slow/failed drain or fill, related error codes
• Restores reliable connections when used with properly seated clamps

• Disconnect power and shut off water supply before servicing; allow hot parts to cool
• Place towels or a shallow pan to catch residual water
• Note routing and clamp locations; transfer or replace clamps as needed and seat the hose fully on fittings
• Test for leaks with a short cycle and re-check all connections

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

Note: Quantity of 1 pad, order as needed. Measures about 3.5" x 3.5".

This drive motor powers the appliance's primary motion, converting electrical energy into steady rotation for normal operation. Replacing a weak, noisy, or failed motor restores reliable movement and helps cycles start and finish as expected.

• Supplies rotational torque to drive the drum, agitator, or pump/impeller as commanded by the control
• Common symptoms: unit won't start or the mechanism doesn't move
• Humming, grinding, or intermittent operation under load
• Overheating, burning odor, or tripping a breaker/fuse

• Disconnect power; shut off gas/water supplies if present
• Photograph wire routing; transfer any brackets, pulleys, grommets, or hardware from the original motor
• Verify mounting orientation, belt/pulley alignment, and free shaft rotation before reassembly
• Run a short test cycle and check for abnormal noise or vibration after installation

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

This is the appliance's main electronic control board. It manages cycles, sensors, and power to key components so the unit runs the selected settings reliably.

• Directs and times functions like fill, agitation/tumble, drain, and spin/heating as designed
• Can help with error/fault codes related to the central control

• Disconnect power before servicing; follow ESD (anti-static) precautions when handling the board
• Take photos of wire connections before removal and transfer connectors one at a time
• Mount the board securely in the control housing; avoid pinching harnesses
• After installation, restore power and run a diagnostic or test cycle to verify operation

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Includes connector and both clamps.

Contains two, six foot long braided hoses with 90 degree ends.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

The Main Control Board is an OEM component specifically designed for Whirlpool washers. It is the central processing unit that regulates all cycle functions.

The control board plays a vital role in monitoring water levels, activating motors, heating elements, and detergent dispensing. Precise timings and customized options are accessible through an intuitive LED display.

Causes of a bad control board include water damage, damaging electrical pathways, or power surges corrupting programming over time.

Symptoms of a bad control board include:

• Inability to start or complete desired cycles  
• Flashing error lights on the control panel
• Unbalanced loads triggering imbalance switches
• Drum failing to rotate or fill as directed

This critical board powers the decision-maker behind perfectly clean loads. With its built-in control algorithms, an OEM replacement ensures like-new performance.

This Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Roper models.

Used from harness to top.

This replacement filter captures airborne grease and cooking particles from the vent system. It helps protect the blower and ducting and keeps airflow efficient so your hood or microwave-hood can clear smoke and odors more effectively. What it does:

• Traps grease and food particles to reduce buildup inside the vent path
• Helps maintain proper airflow and ventilation performance
• Replace when torn, warped, heavily saturated, or won't stay seated
• Common symptoms: lingering odors or smoke, greasy residue near the cooktop, visible damage to the filter

• 1 filter

• Disconnect power and allow the appliance and filters to cool before servicing
• Release the retaining tabs or latch and remove the old filter
• Seat the new filter fully and secure per your user guide
• Do not operate the appliance without all required filters installed

Right hand side. For screws use WPW10119828.