Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This middle spray arm assembly mounts at the center wash level and distributes pressurized water across both racks. Replacing a damaged or clogged arm restores even spray coverage and helps resolve weak cleaning performance, especially on the upper rack.
Replaced Middle Spray Arm Hub and Arm Spray Middle Asm. Works like a charm now. Read more
Fix dishwasher overfilling or not filling properly by replacing the float dome. Snaps onto the float assembly to control water level. DIY repair.
Exact GE part, so perfect. Thank you! Read more
I found the schematics on your site and took my best guess at the individual components that I should replace, related to the flood switch. I guessed correctly. Read more
This display control module manages the digital interface and electronic controls on your dishwasher's control panel. It processes cycle selections and displays status information during operation. Replace this board if the display is blank, shows error codes, buttons don't respond, or cycles won't start properly.
I noticed something was wrong when the dishwasher no longer remembered the last cycle performed. After it finished, it would go to a default cycle. A couple of weeks ago, my husband said it wouldn't start. Then I noticed on subsequent washes, there was a high probability that it would hang at a random part of the wash cycle. I was able to reset it though. The last time it stuck was during the pre cycle, where it drains any water and runs the disposer. It hung there all night! I tried cycling... Read more
Remove the unit. Unscrewed filler cup. Put on new part. FIXED PROBLEM. Read more
This was not an obvious source of a leak. The Tower Heater Assembly Nut developed a crack over time due to heat exposure. So the leak was gradual slowly getting worse over time. It was a hairline crack that ran down one of the edges of the nut making it hard to see. In talking to a pro he said it isn't a common problem. It is all the way in the back of the bottom of the dishwasher so it is not something you can see without pulling the dishwasher out and running it. The repair itself is easy. I... Read more
I used lime away, vinegar, finish washer cleaner none of them worked. Finally just use Brillo on the entire cabinet interior. It came out very clean. Only needed very light scrubbing. Then replaced the severely corroded filters Riser tube and upper jet which was not turning. After this the upper arm turned perfectly silverware and glassware and silverware came out rinse very clean. Will do preventative maintenance in the future. Dishwasher was about 5 years old GE Profile high-end Read more
I replaced the keypad. The hardest part was removing all the glue. I tried alcohol and Goof Off. Neither one removed it easily. It came down to patience and rubbing with alcohol. Read more
This turbidity sensor monitors wash water clarity so the machine can adjust wash cycles and rinse times for cleaner results and efficient water use. It replaces a failed or inconsistent turbidity reading to restore proper load sensing. What it does:
Found a service manual that is close enough to my GE dishwasher. Service Manual for GE Dishwasher-EDW4000 was found on the following webpage. http://www.applianceaid.com/pdf/serv-man-EDW4000.pdf Gives enough information to test out the dishwasher. Read it, check out Factory Test Mode. GE should have given this out as a normal User Manual. The usual user manual lack anything to help troubleshoot a problem. Read more
This is a genuine OEM replacement lower spray arm bearing sourced directly from the manufacturer for use in dishwashers. The lower spray arm spins to distribute water to the dishes during the wash cycle. Thus spray arm bearing supports the spray arm and lessens the friction, which allows it to spin more easily. If the dishes are not clean after the wash and rinse cycle, or the arm is making loud noises, the spin arm bearing may need to be replaced. This bearing is a small metal part that may wear over time. If the bearing is distorted or damaged, the arm will not sit level, and spinning may be very loud, or it may not spin. The spray arm bearing should be replaced. Turn off the breaker or disconnect the power to the dishwasher. Open the dishwasher and pull the bottom rack out. Turn the lower spray arm counterclockwise to remove it. Use a telescoping magnet to pull the bearing up from the hole in the middle. Install the new bearing and reinstall the spray arm. Put the dishrack back inside and reconnect the power.This lower spray arm bearing is a gray metal part that is sold individually. It is designed for use in dishwashers designed by General Electric and Hotpoint.
The main conduit was broken and the pump connector had a hole in it. The pump also was showing signs of leaking. I completely disassembled the dishwasher cleaned everything and reassembled. The repair videos are a big help. Thank you. Read more
Replaced all of the broken parts with the new parts from Appliance Parts Pros. Read more
The front door of a dishwasher is operated in part by the use of door springs. There are typically two door springs on most models. The door spring helps the user open and shut the door efficiently. If the door springs are worn out or broken, a replacement part is required.A visual inspection will determine if a door spring is missing, damaged, or worn out. If the dishwasher door no longer opens and closes smoothly, it's an indication that a repair is required. Replacing a dishwasher door spring is a straightforward process. Locate the existing springs and remove them. Line up the new door springs and hook the ends into place. Wear gloves for protection. Disconnect the dishwasher before starting the replacement.This door spring is an authentic OEM replacement part. It is sold individually. The component is made of durable, high-quality metal materials. The replacement door spring comes sourced directly from the manufacturer. The door spring is fitting for several different models of dishwashers. The part can be installed in General Electric, Hotpoint, and RCA devices.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.