Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Size: 10-24 x 3/8 inch.
Replaced timer control unit, first time doing this. Read more
Note: This part is one screw, order quantity needed.
The door hinges on my Maytag Neptune stacked washer/dryer where corroded badly. Took the time to replace the two hinges and repairing the epoxy coating on the front panel of the machine. Unit looks like new. Read more
Dryer won't heat or overheats? This high limit thermostat cuts power when temperatures get too high. Common fix for no-heat issues. Easy install.
When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more
This assembly includes the roller shaft and rear support bracket that holds a drum support roller in place inside the dryer. It allows the drum to rotate smoothly on its rear support rollers. Replace this part if the dryer is making squealing, thumping, or rumbling noises, or if the existing shaft is worn, bent, or seized.
Replaced the roller and shaft. The roller had worn 1/4 of the way through the support shaft. Read more
This cabinet top clip is a small plastic retainer that secures the appliance's top/cabinet to the chassis, keeping the cabinet aligned and preventing movement or rattling. It restores a flush fit between the cabinet and body. What it does:
I replaced the fill valve assembly with a new one. Had to look carefully at the parts diagrams to make sure I ordered the right one since the serial number break old vs. new didn't seem to match the number on my machine. On this particular machine you don't need to pull it out too far from the wall-leave the hoses connected to the valve, remove the screw holding the valve bracket, and pull into the washing machine where you can easily access the hose ends. A putty knife is needed to open... Read more
This switch retainer clip secures a small appliance switch in place so the switch stays aligned and operates correctly. It helps maintain reliable switch contact for normal door or control functions. What it does:
This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it does:
Repair was super-easy following the appliancepartspros.com video! I followed it step-by-step and was done in less than 10 minutes! Saved at least $100 by not having an appliance repair person come in... not to mention a ton of time! Read more
Felt pad.
Removed front wall of dryer, disconnected electrical from wall(first thing). Disconnect front door switch, remove tub, remove felt, clean, used compressed air to blow out all dust from heater assembly. Used compressed air to blow out all lint catch line parts. Used electrical contact cleaner to clean all electrical connections where dust and lint had gathered. Installed new felt pad by first applying high temp adhesive, let adhesive set about a minute or so, install felt. Let sit for about... Read more
One piece. Works on most Maytag washers. Color: white. It measures about 5 inches in diameter, and 5-1/2 inches high.
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more
Usually ships within 4 - 14 days
This is a lint duct housing kit that directs airflow from the dryer drum through the lint screen area and toward the exhaust vent. It forms the internal ductwork that channels warm, lint-laden air so it passes through the lint filter before exiting the dryer. Replace this housing if it is cracked, melted, or damaged, which can cause poor drying performance, longer cycle times, or lint buildup inside the dryer cabinet.
Took a screw driver lifted the top, Unscrewed two screws holding the front on the inside of the dryer one to left and one to the right. Laid the front on the floor and removed to other screws holding the collector in place, popped out old one cleaned all the lint and dust and popped the new one in put the new seal in place and done ! Read more
Seals the gap between the dryer drum and front panel to prevent air leaks and protect clothes from damage. Replace if worn, torn, or causing black marks on laundry.
I replaced the belt and glued the felt seal on. Good as new. I estimate I saved at least $300. This website is amazing. I can't imagine being a homeowner before the internet. Read more
Supports the front of your dryer drum for smooth rotation. Replace when you hear scraping noises or the drum wobbles. Confirm fit with your model number.
First time DIY dryer repair. Videos very helpful! Remove front. Found glides worn thin, paint on drum removed where glides located. Drum, cage and motor turned easily - must be OK. Thirteen year old dryer. Order glides & felt, might as well replace belt and rollers while there. First time order - could not have been easier! Received 2nd day. Replaced parts, reassembled & connected power. Ran for 3 minutes with scraping noise then stopped with burning odor. Disassembled dryer, smelled odor from... Read more
Converting your gas dryer from natural gas to liquid propane? This LP conversion kit modifies the fuel orifice and components. Typical install: 1 hour.
Simple fix with YouTube and kit, only trouble was FedEx loosing my package, APP quickly replaced it. Customer service was great with APP.com Read more
Supports the front of the dryer drum for smooth rotation. Replace if drum is noisy, wobbling, or causes overheating. Verify fit with your model number.
New glides, idler had a crack, blower retaining ring was gone. And a good clean out. Like new again for 2 hours and $77.00 Read more
A plumbing supply store found the part on the internet with a Whirlpool part #. I found that number on the website of another parts supplier (Appliance Zone) but it did not have a picture of the part. It was called a gas connector, and I ordered the part. It arrived quickly, but the name on the parts bag was "elbow". It was only the elbow. I couldn't believe that someone would sell half of a union. I did more searching and found your website which had a picture and description of a "Elbow Union... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.