Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Plastic water line that connects the water inlet valve to the ice maker. Replace if cracked, leaking, or damaged. Includes installation video.
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more
Rubber grommet seals the ice maker fill tube where it enters the refrigerator cabinet. Replace if cracked, brittle, leaking, or missing to restore seal.
Ice not dispensing or slow ice flow? This ice bucket and auger assembly stores and moves ice to your dispenser. Simple DIY install in 10-30 minutes.
I ordered a new bucket and auger combination--I didn't want to have to completely disassemble the mechanism to replace the rusted auger helix dispenser, so for about twice the cost of the auger alone I got the complete assembly. The product arrived in pristine condition less than 48 hours after I purchased it online. About 10 minutes later (most of that spent taking out the old bucket and finding my philips head screwdriver), I had removed the four screws holding the cover plate on the old... Read more
Replaces worn or broken hinge cam riser on the lower door hinge. Restores smooth door lift and closing action. Essential when door sags or grinds.
I made a lucky guess when I ordered the part as I had no model # or anything to go by. I just ordered what looked like the right thing and it was the exact part for my fridge. Replacement was easy. Read more
Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.
Replaced the water supply valve...boom! Read more
Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
Ice dispenser door won't open or solenoid buzzing? This door solenoid assembly controls the ice chute flapper. Moderate DIY repair with video guide.
I ordered a new solenoid and when it arrived, I installed it as follows: I cut the power to the refrigerator. I then pulled off the rubber boot (and it's plastic frame) that covers the water switch. Then I removed the bezel that covers the front of the ice maker controls by pulling it straight out. Then I removed the four screws found on the assembly under the bezel. After pulling the assembly forward a bit, I detached the multi-wire connector attached to it and put the assembly aside.... Read more
Refrigerator not cooling or compressor clicking on and off? This compressor kit restores cooling. Requires certified technician with specialty tools.
Replacement door handle for GE side-by-side refrigerators. Install this handle when your original is cracked, broken, discolored, or worn from years of use.
Replaced with new handles Read more
Secures the ice chute flapper in your refrigerator door. Replace if cracked or missing to restore proper sealing and prevent frost buildup. Verify fit.
I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well. Read more
Ice dispenser not working or making humming noise? This auger motor drives the crusher mechanism to feed ice through the chute. Moderate DIY repair.
I watched the help videos first, then ordered the parts, and installed all items as in the video. Read more
Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.
Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge. Read more
Black hex washer screw for securing range components like door trim, control panels, and internal brackets. Replace missing or stripped screws during repairs.
I ordered the part and was impressed to receive it within two day! I didn't need the screws I ordered (which I ordered just in case) but the trim was put on with no problem and my oven looks brand new again! Thank you! Read more
Freezer not cooling evenly or food freezing? A failed evaporator fan motor stops cold air circulation. This repair restores proper airflow and temps.
Replaced the Evaporator Motor Read more
Rubber grommet that mounts and cushions the compressor on your refrigerator or freezer. Replace if cracked, worn, or causing vibration noise from unit.
Installed new stainless steel pan replacing broken original plastic pan and installed new rubber grommets for the compressor Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
The auger gearbox shaft had a spot that was stripped of threads which prevented the auger drive from spinning the ice down the chute. I replaced the auger motor/gearbox assembly, the auger drive as it had to be cut off the shaft, and the 3 mount bolts that hold it all in place. Whole job took 30 minutes from start to finish which included cutting off the drive bracket. Read more