Tfx25 Parts

This refrigerator lamp socket holds an E12-base appliance bulb and provides the electrical connection for the light fixture. Replace it when the light won't turn on or flickers despite a known-good bulb and functioning door switch.

• Secures an E12 (candelabra) bulb and supplies power to it
• Works with the door/light switch to illuminate the compartment or dispenser area
• Typical failures include heat damage, cracking, or internal contact wear
• Symptoms: no light, intermittent flicker, or a bulb that won't seat firmly

• Disconnect power to the refrigerator before servicing
• Remove any lens/cover, note wire placement, and install the new socket in the original orientation
• Use an E12-base appliance bulb with the wattage specified on your model's rating label
• Restore power and verify operation with the door switch

Refrigerator primary ice and water dual coil water inlet valve. For the filter valve order WR57X10024. For the assembly including both the primary and filter valve having the short bracket order WR57X10026. For the assembly including both the primary and filter valve having the long bracket order WR57X10022.

This replacement motor powers the dispenser's auger/crusher mechanism to move ice from the bucket to the chute. Replacing a weak or seized motor helps restore reliable cube or crushed-ice dispensing from the freezer door.

• Drives the ice auger/crusher to feed ice from the bucket through the dispenser chute
• Helps deliver cubes or crushed ice, depending on the control selection
• Common symptoms: no ice dispensing, auger not turning, loud humming or grinding, intermittent or weak dispensing
• Located in the freezer-door dispenser assembly and engages the ice bucket coupler

• Disconnect power to the refrigerator before servicing
• Remove the ice bucket and dispenser trim/panel to access the motor; note wire orientation and fasteners
• Transfer any mounting hardware or coupler from the old motor
• Reassemble, restore power, and test ice dispensing

The Door Handle is an OEM part for GE refrigerators. This part provides a secure and comfortable grip for opening and closing the refrigerator door.  

Causes of a bad door handle can include regular wear and tear, accidental impact, or repeated use, which can lead to cracks, breaks, or loosening of the handle.  

Symptoms of a bad door handle include:

• The handle feeling loose or wobbly
• Difficulty in opening or closing the door
• Visible cracks or breaks in the handle
• The handle detaching from the door

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

Door solenoid with plunger.

This water inlet valve controls the flow of household water into the refrigerator's ice maker during fill cycles. Replacing a sticking or leaking valve restores proper ice fills and helps prevent nuisance leaks at the back of the unit. What it does:

• Opens when energized to supply water to the ice maker, then closes to stop flow
• Common symptoms: no ice production, weak/empty fills, or leaking from the rear valve area
• Ice maker overfilling or fill-tube icing from a valve that doesn't fully close
• Humming/buzzing from the valve with little or no water flow

• 1 water inlet valve assembly

• Disconnect power and shut off the water supply before servicing
• Pull the refrigerator forward to access the rear; place a towel to catch residual water
• Transfer any mounting bracket/tubing from the old valve and secure all connections firmly
• Restore water and power, then check every connection for leaks while the ice maker cycles

This dispenser crank links the dispenser solenoid and the ice chute door. When you press the dispenser lever, the crank pivots to open and close the ice door so cubes or crushed ice can dispense cleanly without warm air leaking into the freezer.

• Connects the solenoid to the ice chute door to control door movement
• Helps seal the chute when not dispensing to reduce frost and moisture issues
• Common failure signs include ice door not opening/closing, constant frost around chute, or warm/moist air leakage at dispenser
• Can cause ice clumping, frost buildup, or water/ice dispensed irregularly when worn or broken

• Disconnect power before servicing the dispenser area
• Access typically requires removing the dispenser front panel and trim; use care with plastic tabs and wiring
• Note linkage orientation to the solenoid and door flap before removal
• Inspect related parts for wear while open

Black. 8-18 AB HXW 3/8

This evaporator fan motor sits in the freezer and moves air across the evaporator coil, pushing chilled air throughout the compartments. Replacing a weak or failed motor restores proper airflow and more consistent temperatures.

• Circulates air across the evaporator coil to remove heat
• Distributes cold air to the refrigerator and freezer sections
• Helps maintain even temperatures and reduces warm spots
• Common symptoms: no airflow or fan noise, warm fresh food section, intermittent operation, or loud squealing/grinding from the freezer area

• Disconnect power before servicing; wear cut-resistant gloves
• Access from the freezer by removing the rear interior panel; clear any ice obstruction
• Transfer fan blade, bracket, and hardware from the old motor if applicable
• Ensure the blade spins freely and wiring connections are secure before restoring power

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

This part is a lower tail handle. This is a genuine OEM part made by General Electric and has been sourced directly from the manufacturer. This part is intended to replace a broken or detached tail handle on multiple different models and brands of refrigerators. The tail handle fixes to the exterior of the refrigerator. A missing or broken tail handle can prevent the door from functioning properly. The tail handle can become detached from the appliance with regular use and may require replacement. Always ensure the appliance is disconnected from its power source before attempting any repairs. Take appropriate safety precautions and wear protective work gloves. Proper tools are needed to install this part. For more accurate installation information on how and where to install this replacement lower tail handle, refer to the original manufacturer diagrams or owner's manual.As an authentic replacement part, this lower tail handle is suitable for use on various models of refrigerators manufactured by General Electric and Hotpoint. Please note that this is a genuine part made of high-quality and durable plastic and is sold individually.

This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.

• Secures covers, brackets, and trim to the appliance cabinet or liner
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration noise and loose or misaligned parts
• Maintains proper fit of guards, kickplates, or internal panels

• Disconnect power; turn off water supply if working near water lines
• Match to the original fastener to size and thread
• Start threads by hand to avoid cross-threading; tighten snugly, not excessively
• If threading into plastic, avoid overtightening to prevent damage

Size: 10-32 GXTT FLP.595 S

This PTCR is the compressor's start device for select refrigerators. It helps the compressor start smoothly by momentarily boosting the start winding, then automatically reduces current as the motor reaches speed.

• Provides initial start assist to the compressor, then self-resets
• A failing PTCR can cause clicking, repeated start attempts, warm temperatures, or the compressor not running
• Helps protect the compressor by limiting inrush current during startup

• Disconnect power before servicing; allow components to cool
• Note wire positions and orientation before removal
• Inspect compressor terminals for heat damage and ensure firm connections
• If the old device shows signs of overheating, also check the overload and wiring

This clamp secures small hoses or tubing and nearby wiring inside the appliance to keep lines held in place and reduce rubbing, leaks, or vibration noise. It's a direct-fit replacement designed to restore proper hose routing and stability. What it does:

• Holds water, drain or vent tubing securely to prevent sagging and rubbing that can cause leaks or wear
• Keeps hoses and wires aligned to reduce vibration and rattling during operation
• Helps maintain proper connections at fittings so seals stay seated and drip risk is minimized
• Simple mechanical clip action — no special tools or adhesives required

• Disconnect power and shut off the water supply before starting any repair
• Remove the old clamp and install this clamp in the same orientation; tubing sits fully in the fitting
• Use standard pliers (or the OEM-recommended tool) to compress/seat the clamp; avoid twisting or pinching the tubing
• Inspect surrounding tubing and fittings for wear; replace damaged hoses or seals if found