Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Refrigerator not cooling or compressor overheating? The condenser fan motor circulates air through coils to dissipate heat. DIY repair in under 30 minutes.
I googled the issue and read several articles. Most started with cleaning the coils (which mine are on the bottom) (19yr old Kenmore 363.9557812). I had not really ever cleaned them well, vacuuming did little. I had to remove the cardboard cover off the back of the frig, and blew them clean (front to back). Once that was done, I started cleaning from the back and noticed the fan wasn't turning week (condensor fan). Blew it out too, have it a good soon with a pencil, it puffed out a bunch of... Read more
Freezer not cooling or making buzzing noise? The evaporator fan blade circulates cold air. Easy DIY fix in under 5 minutes—simply pull off and press on.
I used a set of ring pliers to remove the old retaining ring, then spread the plastic ribs around the fan motor shaft with a small flat bladed screwdriver to ease removal of the old fan blade. I reversed the process to replace the blade, gently tapping a socket from my socket wrench set placed over the motor shaft and ribs with a small rubber mallet. I stopped when the shaft protruded about 1/8" beyond the plastic ribs of the new fan blade, then installed the new retaining clamp ring with the... Read more
Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.
I replaced the lever asm. and spring Read more
Ice maker not producing ice or won't dispense cubes? This complete ice maker assembly replaces failed units. DIY-friendly install in under 10 minutes.
I found that the Ice Maker in my GE side by side made ice but would not kick out the ice when it had formed, the heating element or the switch that controls it didn't work. I ordered a new ice maker switched it out took less than 3 minutes. The cord was very stiff and just long enough but I got it to connect and in 35-40 minutes I had fresh ICE!! Read more
Rubber grommet seals the ice maker fill tube where it enters the refrigerator cabinet. Replace if cracked, brittle, leaking, or missing to restore seal.
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more
This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.
Replaced the water supply valve...boom! Read more
The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.
Replaced springs, flapper assembly and ice door retainer as described in videos and it was easy. So far so good..water dispenses. Read more
Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
Door solenoid with plunger.
I ordered a new solenoid and when it arrived, I installed it as follows: I cut the power to the refrigerator. I then pulled off the rubber boot (and it's plastic frame) that covers the water switch. Then I removed the bezel that covers the front of the ice maker controls by pulling it straight out. Then I removed the four screws found on the assembly under the bezel. After pulling the assembly forward a bit, I detached the multi-wire connector attached to it and put the assembly aside.... Read more
This replacement motor powers the dispenser's auger/crusher mechanism to move ice from the bucket to the chute. Replacing a weak or seized motor helps restore reliable cube or crushed-ice dispensing from the freezer door.
I watched the help videos first, then ordered the parts, and installed all items as in the video. Read more
Freezer not cooling evenly or food freezing? A failed evaporator fan motor stops cold air circulation. This repair restores proper airflow and temps.
Replaced the Evaporator Motor Read more
Size: 10-32 GXTT FLP.595 S
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
Replaced the water tank. Followed the video instruction provided by Appliance Parts Pros. Very good instruction. Read more
Fix no ice, weak water flow, or leaking with a new water inlet valve. Controls water to your ice maker and dispenser. DIY-friendly repair.
Needed to replace the water valve. Ordered the part Sunday afternoon and it arrived Tuesday morning. Installation was simple especially after watching the online repair video. The most difficult part of the installation process was moving the refrigerator out from its location in order to get access to the back. Read more
Replacement mounting screw for refrigerator panels, brackets, and hardware. Restores secure fit when original is missing, stripped, or corroded.
Hinge missing screws. Replaced 2. Perfect now Read more
Small cabinet roller that allows your freezer to glide smoothly for cleaning or service. Replace worn, cracked, or missing wheels to restore movement.
I cleaned the coils as best as I could with a special brush and replaced the seized up fan motor. Read more