Whrilpool Parts

The Washer Fill Hoses are OEM parts for various washing machines, specifically designed to transport hot and cold water from the home's supply lines to the washer. These hoses are essential for the proper functioning of the washing machine, ensuring a steady and reliable flow of water during the wash and rinse cycles. Coming in packs of 2, each hose measures 5 ft.

Causes of bad washer fill hoses can include wear and tear over time, exposure to high water pressure, or damage from kinks and bends. Additionally, hoses can deteriorate due to exposure to harsh water conditions or chemical buildup.

Symptoms of bad washer fill hoses include:

• Leaks or puddles around the washing machine
• Reduced water flow into the washer
• Visible cracks or bulges in the hoses
• The washer taking longer than usual to fill with water

These washer fill hoses are compatible with a variety of washing machine brands and models, ensuring a secure and efficient water supply.

The Pulsator Coupling is an OEM replacement part for GE washing machines. It is a component located inside the washer tub that allows for the connection and movement of the agitator. The coupling pulsator works with the drive motor to rotate the agitator back and forth during the wash cycle, helping to thoroughly clean clothes through agitation.

Causes of a bad pulsator coupling include wear and tear over time, damage due to impact or foreign objects getting lodged in the mechanism, or deterioration of internal components that restrict proper movement.

Symptoms of a bad pulsator coupling include:

• The agitator not spinning or rotating as it should
• Grinding or clicking noises coming from the tub area
• Vibrations felt in the top of the washer
• Improper agitation, resulting in poor cleaning performance

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lid Assembly is an OEM part for GE washing machines. This part is the lid of the washer. It is essential for securely covering the washer drum, preventing water from splashing out during the wash cycle, and allowing safe operation by ensuring the washer does not run with the lid open.

Causes of a bad lid assembly can include general wear and tear, physical damage from heavy loads or impacts, or issues with the hinges or latch mechanisms.

Symptoms of a bad lid assembly include:

• Difficulty in opening or closing the lid
• Washer not starting or stopping mid-cycle due to a faulty lid switch
• Visible cracks or damage on the lid
• Water leaking from the top of the washer

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The anti-siphon clip secures the washer's drain hose to a standpipe or laundry tub, maintaining the proper air gap to prevent siphoning and backflow. It keeps the hose stable so the washer fills and drains as intended.

• Maintains an air break at the drain to help stop unintended siphoning
• Holds the drain hose securely to a standpipe or sink/tub
• Helps prevent "filling and draining at the same time" or low water levels
• Helps keep the hose from vibrating loose or popping out during cycles

• Unplug the appliance and shut off water before starting
• Route the drain hose per the installation manual; avoid kinks or submerging the hose end
• Snap the clip onto the hose and fasten it to the standpipe or tub edge
• Run a quick test to verify no leaks and correct hose position

The Lid Switch Kit is an OEM part for GE washing machines. This part detects whether the washer lid is closed, and allows the machine to operate only when the lid is properly shut. This safety feature prevents the washer from running when the lid is open, ensuring safe and efficient operation. For the magnet assembly order WH12X10276.

Causes of a bad lid switch can include wear and tear from regular use, electrical issues, or physical damage from rough handling.  

Symptoms of a bad lid switch include:

• The washing machine not starting or stopping mid-cycle
• The washer not agitating or spinning
• The machine running only when the lid is manually pressed down
• Error codes related to the lid switch

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Tub Dampening Strap Retainer is an OEM part for GE washing machines. This part holds the tub dampening straps in place, which help to stabilize the washing machine tub during operation.  

Causes of a bad retainer can include regular wear and tear, physical damage from heavy loads or impacts, and degradation over time. 

Symptoms of a bad tub dampening strap retainer include:

• Excessive vibration or shaking during wash cycles
• Increased noise levels during operation
• The washing machine moving or becoming unbalanced during use
• Visible damage or wear on the retainer or straps

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

A replacement baffle screw and flat washer used to secure the baffle or trim piece in ovens and ranges. Restores proper attachment to reduce vibration and keep the baffle aligned for normal operation. What it does

• Secures the baffle or trim to the oven/range body and prevents movement or rattling.
• Replaces missing, stripped, or corroded mounting hardware that can cause loose or misaligned baffles.
• Helps maintain a tight fit so trim and baffle sit flush with surrounding panels.
• Small, direct-replacement fastener for original baffle mounting points.

• Disconnect power and allow the appliance to cool before accessing internal panels.
• Use the matching size screwdriver; start threads by hand to avoid cross-threading.
• Tighten until snug — avoid over-tightening, which can strip threads or deform the washer.
• Repair or replace the mounting bracket before installing this hardware.

This flood hose gasket seals the joint where the washer's flood/overflow hose connects to the outer tub. A fresh seal helps stop seepage from the tub area, preventing drips or moisture around the top or rear of the washer.

• Creates a watertight seal at the flood/overflow hose connection to the outer tub
• Helps prevent leaks during fill, wash, and spin
• Typical failure signs: drips from the top/back of the tub, visible cracks or deformation, or a loose hose connection

• Disconnect power and turn off water supply before servicing
• Access the flood hose connection at the tub; remove the hose and old gasket
• Seat the new gasket fully and reconnect the hose securely
• Run a short cycle to check for leaks

This drive pulley mounts to the washer basket shaft and routes the belt from the motor to spin the drum. Replacing a worn pulley can stop squeal and belt slippage and help restore smooth, reliable spin performance.

• Transfers motor power via the belt to rotate the wash basket during spin
• Keeps the belt tracking correctly; damage can cause squealing, fraying, or slippage
• Typical symptoms: no or slow spin, belt repeatedly coming off, grinding/squealing noises, burning rubber smell, or visible pulley wobble

• Disconnect power and water before servicing; pull the unit forward for access
• Remove the rear panel to access the belt and pulley
• Slip off the belt, remove the center fastener, and replace the pulley
• Reinstall the belt on the grooves; verify alignment by hand-rotating the drum before testing

A 1/4-20 x 5/8 hex washer-head machine screw that secures brackets, panels, and internal components in your appliance. Using the correct fastener keeps assemblies tight to help reduce vibration, rattling, and alignment issues.

• Provides the specified 1/4-20 machine-thread fastening for designated mounting points
• Replaces a missing, stripped, or damaged mounting screw
• Helps reduce loose-component rattles and vibration
• Maintains proper alignment of brackets, panels, and hardware

• Disconnect power; for washers, also shut off water before service
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• Use the appropriate nut driver or socket for the hex-washer head
• Install only where this thread and length are specified by the manufacturer

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

Size: 10-12 a. Includes 12 screws.

This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.

• Locks a knob, lever, or similar component onto its shaft/post to prevent it from slipping off
• Maintains a firm fit to reduce wobble and intermittent control engagement
• Replace if the clip is bent, fatigued, corroded, or missing
• Typical symptoms include a knob that falls off, feels loose, or spins without engaging

• Disconnect power to the appliance; turn off water supply for washers
• Pull the affected component straight off to access the clip
• Use needle-nose pliers to remove/install the clip; avoid deforming it
• Ensure the clip is fully seated; test for a snug fit before reassembly

This washer water level pressure switch senses tub fill via air pressure and tells the control when to stop filling and advance. Replacing a failed switch restores accurate water levels to prevent overfilling, underfilling, and cycle stalls.

• Monitors air pressure from the tub through a small hose to determine the selected water level
• Signals the timer/control to open/close the inlet valves and move the cycle to agitation/spin
• Symptoms include overfilling or not stopping fill, little or no fill, or cycles that won't advance because "full" isn't detected
• Water level doesn't match the selector setting or changes unpredictably

• Disconnect power and shut off water supply before servicing
• Access the control console; label or photograph wire locations and transfer them to the new switch one at a time
• Move the existing pressure hose to the new switch; ensure the hose is clear, not kinked or cracked, and fully seated
• Reinstall the knob/control panel and test fill at multiple level settings; access and steps may vary by model

Control the water going into your washer with this triple water inlet valve. Three solenoids open and close to deliver water to the correct fill circuits or dispensers so cycles start and dispensing happens where it should.

• Regulates water flow into the washer when energized by the control
• Routes water to the correct fill path or dispenser compartment via three independently controlled outlets
• Common symptoms: no fill or slow fill, only certain cycles/dispensers receive water, water drips into the tub when off, or leaks at the valve/hose connections

• Unplug the washer and shut off the water supply before servicing
• Place towels, disconnect inlet hoses, and label/photograph wire connectors and outlet hoses for correct reassembly
• Transfer any mounting hardware from the old valve if required; ensure hoses/orientation match their original positions
• Restore water and power, then check all connections for leaks and run a test fill

This double-style hinge bushing supports the washer lid hinge pin and provides a smooth bearing surface. Replacing a worn bushing restores quiet, even lid movement and helps keep the lid properly aligned over time.

• Supports and centers the lid at the hinge
• Provides a low-friction bearing surface for the hinge pin/rod
• Helps reduce squeaking, looseness, and metal-on-metal wear
• Can help resolve a wobbly, misaligned, or scraping lid

• Disconnect power before servicing; support the lid to prevent dropping
• Remove the hinge pin/rod or screws as your model requires to access the bushing
• Pry out the worn bushing and press the new bushing fully into the hinge opening
• Reassemble and check lid operation; consider replacing the opposite-side bushing if worn