Wtw4800bq Parts

This capacitor stores and releases electrical energy to give the appliance's circuit the boost and stability it needs to start and run properly. Replacing a weak or shorted capacitor can restore reliable operation and reduce strain on related components. What it does

• Provides an energy boost and stabilizes voltage in the designated start/run or power circuit
• Helps motors or power sections energize smoothly and maintain performance
• A failing capacitor may cause humming/buzzing, failure to start or heat, intermittent operation, or tripped fuse/breaker
• May show swelling or signs of overheating around the case or terminals

• 1 capacitor

• Disconnect power before service; capacitors can hold a charge—use a proper discharge procedure before handling
• Note/photograph wire locations; move leads to matching terminals and ensure tight connections
• Mount securely in the original position; re-use brackets/insulators as applicable and keep wiring clear of sharp edges or heat
• After replacement, check the related motor or circuit components if symptoms persist

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

This replacement screw secures panels, brackets, and internal components within your appliance. Replacing a missing or damaged fastener restores a tight fit, reduces vibration and noise, and helps keep parts properly aligned during operation.

• Fastens panels, trim, brackets, or internal components to the chassis
• Maintains proper alignment and stability during normal use
• Replaces missing, rusted, or stripped hardware
• Common symptoms: loose or rattling panels, vibration, difficulty fastening, or a visibly missing screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Match length and thread to the original; replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is stripped, repair threads or replace the clip/nut before installing

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Part of the agitator cam (short) assembly. For complete repair kit use 285809.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This electronic control board is the central "brain" of the appliance. It processes sensor inputs and directs power to key components so cycles run correctly. Replacing a failed board restores normal operation and responsive controls. What it does

• Distributes power to motors, valves, heaters, fans, and displays based on sensor signals
• Manages cycle timing, modes, and overall system logic
• Stores error logic and supports service diagnostics
• Helps protect the system by shutting down functions when faults are detected
• Common symptoms include no power or no response, intermittent operation, error codes/alarms, or components not running

• 1 electronic control board

• Disconnect power before servicing; observe ESD precautions and handle the board by the edges
• Photograph connections and move wire harnesses one at a time to the new board; confirm connector orientation and seating
• Transfer any jumpers, DIP switch positions, brackets, or mounting hardware from the original board as needed
• After installation, restore power and run the model's diagnostic or configuration steps per the tech sheet/service manual if applicable

Includes connector and both clamps.

This replacement nut is a small hardware fastener used to secure components inside your appliance. It helps keep parts tight and properly aligned so assemblies don't loosen from vibration or normal operation.

• Threads onto a mating bolt, stud, or shaft to clamp parts together
• Maintains alignment and reduces movement and rattling
• Replaces a stripped, missing, or damaged nut to restore a secure fit
• Common signs of failure: loose panels or components, unusual vibration/noise, hardware missing

• Disconnect power; shut off gas and/or water if applicable before servicing
• Note the original hardware stack-up (washers/spacers) and orientation for reassembly
• Start by hand to avoid cross-threading; tighten to manufacturer guidance—do not overtighten
• Replace any damaged washers or locking devices

Contains two, six foot long braided hoses with 90 degree ends.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Used from harness to top.