Power Small Engine Spark Plug Parts
Genuine Frigidaire part
By: Frigidaire
Part Number: 131298300
Dryer won't heat or overheats? A failed cycling thermostat can't regulate temperature. This direct-fit part takes 15–30 minutes to replace.
Do-It-Yourself Stories from Customers like You
Rubbing blocks and felt that seal the front of the drum are worn drum is sagging and staining clothes with smears of rust Seth W. • Upper Arlington , OH • January 23, 2016
Replaced upper and lower felts. Painted rubbing surface on inside of drum with refrigerator enamel. Took out drum and lubed rear bearing. Replaced 2 of the 3 thermostats, and the belt just on principle.
Spent a lot of time with shop-vac removing lint from drier and exhaust ducts.
Runs great and is no longer cooking or staining clothes.
Read more
More
$52.76
- Compare At:
-
$62.78
- You Save:
-
$10.02
Genuine Ge part
By: Ge
Part Number: WE04X25194
Dryer not heating or overheating? This thermostat regulates temperature during the drying cycle. Common DIY repair that restores proper heat control.
Do-It-Yourself Stories from Customers like You
Not getting very hot Gore, R. • Silsbee , TX • November 07, 2025
Did it myself.
Read more
More
$34.44
- Compare At:
-
$40.98
- You Save:
-
$6.54
Genuine Whirlpool part
By: Whirlpool
Part Number: WP31001590
Fix a dryer that won't heat or overheats with a new thermistor. This temperature sensor ensures accurate heating cycles. DIY repair in 30 minutes.
Do-It-Yourself Stories from Customers like You
Dryer ran but wouldn't heat the only thing i could find was the thremistor only real at 8 ohms instead of a little over 10 Ross M. • Ohiopyle , PA • October 24, 2016
Installed a new thermistor tempiture control and it heats up as it should.
Tools used was a ohlm meter, 1" stiff puty knife, #2 Philips screw driver, neadle nose pliers,1/4 & 5/16 nut drivers.
Read more
More
$59.48
- Compare At:
-
$71.38
- You Save:
-
$11.90
Genuine Bosch part
By: Bosch
Part Number: 00165263
Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.
Do-It-Yourself Stories from Customers like You
No spray during wash cycle pump impeller was broken. Robert K. • Cazenovia , NY • February 22, 2019
Watched AppliancePartsPros video, disassembled the dishwasher and replace impeller and seals.
Read more
More
$12.16
- Compare At:
-
$12.92
- You Save:
-
$0.76
Genuine Ge part
By: Ge
Part Number: WE1M1002
This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.
- Provides overcurrent protection for the circuit specified by the manufacturer
- If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
- Helps prevent wiring and component damage from shorts or overloads
- Repeated fuse failures indicate an underlying electrical issue requiring diagnosis
What's included: 1 CCMR fuse (30A, 120V) Install notes:
- Disconnect power to the appliance before servicing
- Locate the fuse in its holder/block and inspect associated wiring for heat or damage
- Test the old fuse for continuity; replace only with the identical rating specified
- Never bypass or upsize a fuse; correct the root cause of the failure before returning to service
Do-It-Yourself Stories from Customers like You
The dryer would not turn on Roland S. • Richmond , CA • August 02, 2014
First I check the breaker for the dryer then I check the power cord and the ohms to the power cord when all this things were in working order I then check the ohms to the fuse to the control panel.
The fuse had no ohms so I got a pair on needle nose pliers pulled out the fuse and replace it worked just find after that
Read more
More
$53.69
- Compare At:
-
$64.43
- You Save:
-
$10.74
Genuine Bosch part
By: Bosch
Part Number: 00263088
Detergent door won't close or stay shut? Replace the dispenser assembly. Takes about 20 minutes with basic tools—remove inner door panel and swap out.
Do-It-Yourself Stories from Customers like You
Dispenser no longer opened Douglas L. • Fountain Hills , AZ • April 22, 2014
Removed back of dishwasher with hex screw driver 5 min
Unplugged power cord 30 secs
Loosened metal bracket on top and bottom with screwdriver 5 min
Pushed dispenser in and removed from dishwasher 5 min
Positioned new unit in space and snapped into place 1 min
Plugged electrics back in 1 min
Screwed back on 3 min
Roughly 20 min. I am nontechnical and rarely do repairs.
Read more
More
$210.39
- Compare At:
-
$248.26
- You Save:
-
$37.87
Genuine Lg part
By: Lg
Part Number: 6323EL2001C
This NTC thermistor is the dryer's temperature sensor. It monitors exhaust air temperature and signals the control to cycle the heat, restoring accurate drying performance and helping prevent overheating, underheating, and inconsistent results.
- Monitors exhaust air temperature by changing resistance as heat rises (NTC behavior)
- Sends temperature feedback to the control to regulate the heater or gas valve
- Failure can cause no heat, overheating, or erratic temperatures
- May lead to long dry times, short cycles, or temperature-related error codes
What's included: 1 thermistor Install notes:
- Disconnect power and, for gas models, shut off the gas supply before servicing
- Access the sensor on the blower housing or exhaust duct; location varies by model
- Note wire routing; unplug the harness connector; remove the mounting fastener/clip; install the new sensor fully seated and reconnect
- Reassemble, restore power, and run a test cycle; check and clean venting to ensure proper airflow
More
$31.32
- Compare At:
-
$37.27
- You Save:
-
$5.95
Genuine Lg part
By: Lg
Part Number: 4830ED4001B
Small sleeve bushing that supports pivoting or rotating joints in your dishwasher. Replace when worn, cracked, or causing excess friction between moving parts.
Do-It-Yourself Stories from Customers like You
Missing brackets and screw hole cover Brian S. • Ashland , MO • March 15, 2016
Thanks to LG NOT sending the parts THEY say are included with the dishwasher, I had to buy them in order to install the appliance. I sure hope the LG appliance performs better than their customer service.
Very simple fix....bought the EXACT items needed from AppliancePartsPros.com and in just a matter of two days, had the parts needed. Amazing! Excellent experience.
The fix was attaching the brackets to the cabinet and screwing it to the countertop. Also just popping the screw covers...
Read more
More
$11.60
- Compare At:
-
$13.80
- You Save:
-
$2.20
Genuine Whirlpool part
By: Whirlpool
Part Number: WP31001192
If your dryer is overheating, running too hot, or taking extended times to dry clothes, a faulty cycling thermostat is often the cause. Easy DIY fix.
Do-It-Yourself Stories from Customers like You
No heat on dryer low setting insufficient drying even on high extended times to dry Thomas M. • Galax , VA • June 12, 2016
Ended up replacing the cycling thermostat which corrected the problem. Andrew C. was very helpful with considerations and return of unneeded parts as well as very informative technical assistance. Could not have been treated better.
Read more
More
$79.24
- Compare At:
-
$93.50
- You Save:
-
$14.26
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10131836
Fix dryer underheating or overheating issues with this 140°F fixed thermostat. Restores accurate temperature control and stops erratic cycling. Easy repair.
More
$69.95
- Compare At:
-
$83.24
- You Save:
-
$13.29
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10616003
Soap dispenser door won't latch or detergent stays in compartment? This dishwasher dispenser assembly releases detergent at the right time. Moderate DIY.
This part fixes the following symptoms
-
Will not dispense detergent
See more...
Do-It-Yourself Stories from Customers like You
Soap dispenser door broke Janie C. • Raynham , MA • January 17, 2016
My husband Ron diagnosed the problem, that a new Soap dispenser assembly was needed. We ordered the part, and it arrived in 48 hours. The front dishwasher door was rusty, but my husband managed to dis-assemble and replace the dispenser. Pleased with purchase process. Part fit fine. Janie
Read more
More
$176.46
- Compare At:
-
$209.99
- You Save:
-
$33.53
Genuine Whirlpool part
By: Whirlpool
Part Number: W10169881
Dryer not heating? A blown thermal cut-off is a common cause. This safety fuse opens if overheating occurs. Test with a multimeter for continuity.
Do-It-Yourself Stories from Customers like You
Dryer was not heating Donna G. • Warsaw , MO • August 02, 2014
The first part we ordered was the heating element. The dryer still wasn't heating so we ordered the thermostat. We received the thermostat, and got it put in the dryer still wasn't heating so I consulted my dryer manual and found out that even though there was electric to the dryer it still might not heat if the breaker was not all the way on, so I reset the breaker and voilà had heat. Working very well now.
Read more
More
$73.95
- Compare At:
-
$88.00
- You Save:
-
$14.05
Genuine Frigidaire part
By: Frigidaire
Part Number: 316284100
Spacer that provides clearance between the range oven door handle and door surface. Replace if cracked, broken, or missing to ensure proper handle fit.
Do-It-Yourself Stories from Customers like You
Handle broke Charles H. • Jonesboro , GA • October 04, 2019
I orderd parts you said I needed, but all I needed was a handle. I will keep other parts for future needs
Read more
More
$26.95
- Compare At:
-
$31.80
- You Save:
-
$4.85
Genuine Whirlpool part
By: Whirlpool
Part Number: W10864394
This is a small cap that covers and seals the rinse-aid reservoir on a dishwasher door. It keeps the rinse-aid liquid contained so it dispenses at the correct time during the wash cycle to prevent water spots on dishes. Replace this cap if it is cracked, warped, or no longer seals properly, which can cause rinse-aid to leak out prematurely or result in spotty dishes.
Do-It-Yourself Stories from Customers like You
Dishwasher had melted gasket Valerie W. • Phoenix , AZ • December 05, 2015
Easiest fix ever. Part went right in and a left turn was all that was needed.
Read more
More
$18.55
- Compare At:
-
$22.26
- You Save:
-
$3.71
Genuine Whirlpool part
By: Whirlpool
Part Number: W11165163
The Electrode is an OEM replacement part for Whirlpool dryers. It is responsible for detecting the moisture levels in your laundry during the drying cycle, allowing the dryer to automatically adjust the drying time and temperature. It helps prevent over-drying or under-drying of your clothes, saving energy and protecting them from potential damage.
A bad electrode can occur due to wear and tear, damage, or a buildup of debris or lint. If you notice symptoms such as clothes taking longer to dry, the dryer shutting off prematurely, or inconsistent drying results, it may be time to replace the moisture sensor bar electrode.
Symptoms of a bad electrode include:
- Clothes taking longer to dry than usual
- The dryer shutting off prematurely
- Inconsistent drying results, with some items remaining damp
Repair your dryer by replacing the faulty or damaged electrode with this genuine OEM part.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
More
$50.57
- Compare At:
-
$60.18
- You Save:
-
$9.61
Genuine Ge part
By: Ge
Part Number: WB01X45506
This rivet assembly is a direct-replacement fastening piece used to secure appliance panels and components, restoring a stable, rattle-free fit and preventing movement caused by worn or broken rivets. What it does:
- Secures panels, brackets, or component mounts to restore proper alignment and support
- Stops rattling, vibration, or loose hardware caused by damaged or missing rivets
- Provides a durable mechanical fastener where original rivets have sheared or loosened
- Helps maintain safe operation by keeping parts properly retained
What's included: One rivet assembly Install notes:
- Disconnect power (and gas/water if applicable) before attempting any repairs
- Removal may require drilling out the old rivet; installation typically needs a rivet gun or equivalent tool
- Keep hardware orientation the same as the original; replace any damaged surrounding parts
Do-It-Yourself Stories from Customers like You
Ge microwave: sparking melted hole in stirrer fan cover and it would not run without sparking Henry H. • Swanton , OH • September 10, 2016
I replaced the stirrer fan cover and fan, which had some carbon and slight burn marks on it. It was difficult to remove the fan cover as it did not rotate. I had to pry it off with a flat blade screwdriver, breaking the plastic tabs on the cover (which was being discarded anyway). I then cleaned any visible carbon deposits and replaced the cover and fan, using the old stirrer fan holder as it appeared OK. However, I was unable to rotate the cover into the locked position so I could not insert...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13