Assy-Case Sensor Parts

• Timer will not advance

I went ahead and ordered the element, and the 2 different thermostats not knowing exactly which one might be the problem. My My Maytag opens from the front and it was actually pretty easy to get into. Also gave me the opportunity to vacuum out the inside of the dryer. Pop the top off, remove the wires that connect the door switch (noting the colors and placement), take off the 2 inside nuts that hols the fron on, pull it forward and lift it off, 3 inside screws to take out to inside lint part... Read more

• Freezer not defrosting
• Freezer section too warm

Ended up being the defrost sensor. Ordered the heater and control board just in case. Started with the control board still didn't defrost. replaced the sensor and all is well. Super helpful tech staff answered all my questions... Read more

Got the infamous icemaker freezing up problem so common to Frigidaire Gallery and Professional series refrigerators. I was also only getting the "OP" code on the diagnostic test 26, so I determined the defrost heater and/or the thermostat was probably bad. So, I went ahead and replaced both of them, as well as installed the updated air handler housing kit. What I didn't realize from the parts pictures was that the air handler kit was not only updated foam replacements, but it was also a... Read more

Put both thermostats in as I did not know if the unit was cycling on high limit at times. Fixed both issues plus I used my lawn blower and blew all the lint out of dryer and short 3' hose. I also lubed rear drum bearings. Works like new. Ron R Read more

Replaced 3 low cost parts as advised by Appliance Parts Pros. Saved the labor costs by troubleshooting and replacing parts with their great videos. Works like new, and took 15 minutes to complete the repair. Read more

I removed the defrost sensor assembly, installed a new one, it worked. Because of a shipping problem with FEDEX, Appliancepartspros resent the parts not once but twice. Needless to say, they are my go-to source for parts from now on. Read more

Watched a few of your well put together videos and could not afford a new Refrigerator right now because it was a built in so decided with the frost on the bottom of the freezer grill and the Refrigerator warming up decided to replace the Heater Element and Thermostat Defrost which took some time but so far so good lets hope that is all that is needed saved over 10,000.00 dollars for a new 48" built in for now! Thank you for your rushed order and videos I think you are a life saver got the part... Read more

I have a Bosch nexxt 500 series dryer that stopped heating. It was still running fine, just no heat. I did some research and found the Limiter as the possible problem. I pushed the red reset button. The dryer started heating up, but with in 1 cycle kicked off again. I called A.P.P. and spoke to Cecilia. She was very helpful. After a brief description of my situation she recommended just to replace the Limiter. I did so and that fixed the problem. Very simple replacement. It look longer to take... Read more

After reviewing various posts on the internet, I tested the high heat temperature limiter and determined it was faulty due to lint buildup. Ordered the parts from AppliancePartsPros.com on Friday afternoon and parts were delivered on Saturday afternoon. Replaced the parts- dryer works as good as new. Read more

I replaced the thermal cut-off sensors and the cutoff-Tml Read more

I took and ohm meter to the heating element and figured out that was ok. Went to the thermostat and it was toast. Easy fix. Read more

I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more

I checked the continuity on the thermal fuse (which was blown) and knew that it needed to be replaced. This made me question why it blew (i.e. what caused it to fail). I checked continuity on the thermostat (high limit) as well as the thermostat for the element. Both passed a continuity test, so I removed the high limit thermostat to inspect it and could hear it rattling inside. This leads me to believe the spring inside had failed, so I replaced this thermostat as well. Put it back... Read more

Like a boss! Seriously, removed oven from wall (2 screws), removed about 15 sheet metal screws from front and top covers, unplugged wire harnesses one (or a few) at a time. Reassembled. Hint. Take a picture of wiring before removing and mark old parts (especially thermal fuse) with sharpie before removing so you don't get confused. It's really hard to tell a used electrical part from a new one. Read more