Hardware Hand Small Engine Ignition Coil Parts

Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time. Read more

Knowing from a previous repair, that there was only 3 parts that could be bad. I decided if I was going to take it apart to change all 3. Not having the proper test equipment, it was cheaper to replace the 3 parts than pay a repair person. Read more

Replaced the hinge receiver with a new one. The old one was bent slightly inside where it could not be seen. I think someone pushed the door down to far or fell on it. 2 screws to remove it, take out storage drawer and reach up little ways to remove and replace the receiver. Replace the 2 screws. The receiver comes with 2 screws but I ordered an extra ( never used it ). The sides of the receiver were spread just a tiny bit but were enough to cause a problem. Read more

Removed the defective burner labeled the leads as to their location and coil connections. Replaced the connections to the corresponding locations, 1 to 1, 2 to 2 and the bridged terminal as it was. I noticed that the coils in the replacement burner were not wound in the same direction as the original burner and made note of this. I did not think much of this at the time, but on turning the power back on and lighting up the burners I noticed up they were not lighting up the corresponding... Read more

Range has no model ID plate anywhere. Flip off electric at circuit breaker box. Opened top of range and noted details of the faulty burner, including confirm that outer coil was fried. The maker info on back of element was useless in finding replacement: more useful was general shape, and the numbers around edge on back. Close up range, since low heat element still working. Turns out all Maytag double oven Gemini ranges use the same hi-low element, but double check appearance just in... Read more

Turned stove breaker off in the main breaker box and also unplugged the oven from the 220 outlet. pulled the baking racks out of the oven and proceeded to locate the 1/4 screws just above the bake element where it passes through the metal wall and removed them. pulled the element forward until the wires were exposed and unplugged them and then attached the new element to the wires and reinstalled in reverse order. Read more

Ordered part and installed it. Broiler works as advertised. Read more

• Little to no heat when baking
• Oven not heating evenly

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more

Removed the element "easy just four screws" unplugged two connecting wires, removed element. Did a "continuity test" on element, it failed, so I ordered a new one and installed it. It works great now. Read more

Would advise before doing this repair to watch the video for it. It is not a plug in connection anymore like older ovens. The key is to keep the connecting wires from the oven from falling or pulling into the inner wall of the oven. The wires may not come very far out away from the wall of the oven so make sure to secure them. The video shows a good way to do that. If you have an in wall oven this is very important because it would hard and time consuming to pull the oven out of the wall to... Read more

Replaced the elements with new ones ordered through Appliance Parts Pros. I wanted to tell you how pleased I am that I ordered the baking and broiler elements for my Maytag oven from you. Your website diagrams for my model of oven helped immensely in figuring out what parts I needed. Your order process was easy and the parts arrived within two days just as stated. Best part of all, the new elements work perfectly! I will bookmark your site for future appliance part needs and I look forward to... Read more

Replaced evaporator heater and housing. Just make sure you also replace the thermostat. If not it is a little challenging to get the wires out of the old thermostat/ heater plug into the new plug. Also if you have the same problem be prepared to have a good heat gun to melt the ice buildup around the evaporator and drain hole. The ice build up was so bad that it destroyed the evaporator cover and was leaking into the refrigerator or should I say ice was forming below the evaporator cover... Read more

After watching the video, I replaced the gas valve. Read more

It was very easy caled up ordered the part no prblem got it in 3 days.Got a phillips screw driver removed the top of the stove took out the old one a put in the new one had it fixed within minutes very easy diy no need to pay someone alot of money for this easy fix. Read more