Object Stack Blower Wheel Parts

The Dishrack Roller is an OEM part for GE dishwashers. Mounted within the side walls, this plastic roller guides the dish rack in and out smoothly during loading and unloading. 

Symptoms of a bad dishrack roller include:

• Difficulty pulling or pushing the rack in and out of the tub
• Squeaking or grinding noises produced during rack movement    
• Rack jams or fails to fully extend on retrieval

Causes stem from normal wear of the roller bearing over repeated uses. The durable plastic material is carefully designed for quiet, seamless sliding.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This is a plastic push-on washer motor pulley.

Rubber grommet for motor mount stud.

This dryer blower moves air through the drum, lint filter, and exhaust so laundry dries efficiently. Replacing a damaged blower restores proper airflow and helps prevent long dry times and overheating issues.

• Draws and circulates air across the heater, through the drum and lint filter, and out the vent
• Maintains correct airflow and temperature control for consistent drying performance
• Worn, cracked, or clogged blowers may cause weak exhaust airflow and extended dry cycles
• May also present as rattling/grinding noises from the blower area or high-heat shutoffs

• Disconnect power; if gas, turn off gas supply before servicing
• Access the blower by removing the front/lower panel and blower cover
• Clean lint/debris from the housing and duct; transfer any seals or hardware from the original as needed
• After installation, spin the blower by hand to verify free movement; reassemble and test airflow

This turntable motor drives the coupler and glass tray in your microwave, rotating food for more even heating. Replace a failed or noisy motor to restore smooth, consistent tray movement and reduce cold spots during cooking and reheating.

• Drives the center coupler and glass tray to rotate during operation
• Helps ensure even heating by moving food through the microwave energy field
• Direct replacement when the original motor is seized, noisy, or electrically open
• Symptoms include a tray that won't turn, jerky rotation, or a humming/grinding sound from the turntable area

• Disconnect power before servicing; microwaves contain high-voltage components that can retain a dangerous charge
• Access to the motor is typically from the bottom; remove the cover/panel per your model's service information
• Transfer the two wires to the new motor and secure it with the mounting screws; ensure the shaft fully engages the coupler
• After reassembly, test with a cup of water to ensure smooth rotation

The Blower Wheel is an OEM component specifically designed for GE dryers. It is responsible for circulating air during the drying cycle, directing airflow through lint and clothes to remove moisture. The plastic blades of the blower wheel push air through the dryer and out the vent when the motor is running. 

Symptoms of a bad blower wheel include:

• Slow or inefficient drying times even on low moisture loads    
• Strange noises from inside the dryer cabinet      
• Excessive vibrations felt through the dryer door or cabinet
• Bent or cracked blower wheel blades

Causes can include normal wear and tear over time, accidents that damage the blades, or failures in the secure mounting of the blower wheel.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This kit includes 4 double roller attachments. Enough for one lower rack. Color: white. Each roller attachment measures about 3 inches high by 6 inches deep.

This turntable motor drives the glass tray in your microwave for even heating. Replace it when the tray stops turning, turns intermittently, or the motor makes unusual noises to restore smooth, reliable rotation.

• Rotates the turntable tray/plate for more even cooking and reheating
• Provides steady drive to the tray via the center coupler
• Typical fix for a non-spinning or intermittently spinning turntable
• Can address loud humming or grinding noises from beneath the oven floor

• Disconnect power before servicing; microwaves contain high-voltage components
• Access is typically from the bottom by removing the motor cover or base panel
• Note wire orientation; transfer connectors, align the shaft with the coupler, and secure with the original screws
• After reassembly, place a microwave-safe cup of water on the tray and run briefly to ensure the turntable rotates

This planetary drip ring fits around a stand mixer's planetary assembly to cover the gap below the gearcase and help catch grease residue, restoring a clean, finished look where the beater hub meets the mixer head.

• Mounts at the base of the mixer head around the planetary housing
• Helps deflect incidental gearbox grease residue away from the bowl area
• Covers the seam between housing and planetary for a clean, finished appearance
• Replace if bent, cracked, loose, missing, or if you notice grease spotting beneath the planetary

• Unplug the mixer and remove the bowl and attachments
• Gently pry off the old ring; clean the seating surface of debris or residue
• Align and press the new ring evenly until fully seated; avoid deforming the ring or striking the gearcase
• On some models, access may require lowering/removing the planetary

This evaporator fan blade mounts on the freezer fan motor to move air across the evaporator coils and circulate cold air through the cabinet, helping maintain proper temperatures when the original blade is cracked, warped, or missing.

• Circulates air over the evaporator coils for efficient heat removal and even cooling
• Helps restore airflow between freezer and fresh food sections
• Addresses symptoms such as weak/no airflow from vents, rising temperatures, or rattling/scraping noises from the freezer area
• Replaces a damaged blade that wobbles or rubs the shroud

• Disconnect power; remove freezer shelves/bins and the rear panel to access the fan assembly
• Pull the old blade straight off the motor shaft; avoid prying on or bending the shaft
• Match the orientation of the original and press the new blade onto the shaft until fully seated with clearance to the shroud
• Spin by hand to ensure free movement; reassemble panels and restore power

An evaporator fan blade mounts on the evaporator fan motor to move cold air across the coils and throughout the refrigerator compartments. Replacing a cracked, warped, or loose blade restores proper airflow, temperature balance, and quiet operation.

• Circulates air across the evaporator and into the fresh food and freezer sections to maintain even temperatures
• Helps reduce frost/ice buildup on the evaporator cover by improving airflow after defrost
• Common symptoms of a damaged blade: rattling or scraping noises behind an interior panel, weak or no airflow at vents, warming in the fresh food section, or uneven cooling
• A cracked or loose blade may spin but move little air even when the motor runs

• Disconnect power to the refrigerator before service
• Access the evaporator fan behind the interior rear panel; remove the cover/shroud as required (varies by model)
• Note blade orientation; seat the new blade fully on the motor shaft and verify clearance inside the shroud
• Reassemble panels, restore power, and confirm the fan spins freely without rubbing

This small wheel mounts to the dishwasher rack and lets it roll smoothly along the rails. Replacing a worn or broken wheel restores easy rack movement and helps prevent jams, derailments, and track damage. What it does:

• Provides rolling support so the rack glides in and out on the rails
• Helps keep the rack level and properly aligned
• Replace if the wheel is cracked, flattened, loose, or missing
• Common symptoms: rack binds or falls off track, wobbles, or makes scraping/grinding noises

• 1 wheel

• Disconnect power and water if working inside the tub; for rack-only service, remove the rack and work on a stable surface
• Remove end caps/stops and slide the rack out
• Release the old wheel from its clip/axle and install the new wheel securely
• Reinstall rack and end caps; verify smooth travel on both rails

The Dishwasher Upper Rack Roller Holder Assembly is essential for maintaining the smooth operation of your dishwasher's upper rack. This genuine OEM part ensures a perfect fit with your Samsung dishwasher, providing durable support for the rolling mechanism. Designed to replace worn or damaged roller holders, it restores the full functionality of your appliance, allowing for easy loading and unloading of dishes. The sturdy construction of the HOLDER-ROLLER guarantees long-lasting performance, reducing the need for frequent replacements. Installing this part enhances the stability of the upper rack, preventing unwanted movement during wash cycles and ensuring that your dishes are securely held in place. With its reliable design, the Dishwasher Upper Rack Roller Holder Assembly not only improves the efficiency of your dishwasher but also extends its lifespan. Trust in this genuine OEM part to deliver the quality and performance you expect from your Samsung appliance, making your kitchen routine smoother and more efficient.

This replacement blower wheel for a dryer mounts to the drive motor and pulls air through the drum, lint filter, and exhaust, restoring proper airflow so loads dry efficiently and the appliance runs as intended. What it does:

• Spins with the motor to move air through the drum, lint screen, and exhaust duct
• Maintains airflow needed for even drying and temperature control
• Wear, cracks, or a stripped hub can cause long dry times and weak vent airflow
• Damage or imbalance may produce rattling, scraping, or vibration noises from the blower area

• 1 blower wheel

• Disconnect power; turn off gas supply for gas models before servicing
• Access the blower housing and remove the old wheel from the motor shaft per your model's design
• Clean lint and debris from the blower housing and exhaust duct while open
• Seat the new wheel fully and verify free rotation without rubbing before reassembly

This condenser fan assembly circulates air across the condenser coils and compressor to remove heat from the refrigeration system. Replacing a failing fan helps restore efficient cooling performance and protects the compressor from overheating. What it does:

• Draws air through the condenser coils to dissipate heat
• Supports proper system pressures and overall cooling efficiency
• Helps maintain stable temperatures in both compartments
• Common symptoms include the fan not running, loud noise from the rear, warm cabinet temperatures, or a very hot compressor area

• Pre-assembled fan motor with blade and mounting bracket

• Disconnect power before servicing; use gloves to protect against sharp edges
• Access the lower rear compartment and remove the back cover to reach the fan
• Note wire positions; move over any reusable grommets or screws and secure the assembly firmly
• The blade spins freely and is oriented to move air across the condenser; clean coils before restoring power

This replacement coupling links and seals wash-system components so pressurized water reaches the spray arms. Replacing a cracked or worn coupling restores cleaning performance and helps prevent drips at the connection point.

• Provides a secure, watertight connection within the dishwasher wash system
• Helps deliver proper water flow to the spray arms
• Failure symptoms can include poor cleaning, spray arms not turning, a loose/detached feed tube, or leaks at the connection
• Replace if the coupling is cracked, deformed, or stripped

• Disconnect power and shut off water before servicing
• Remove dish racks and access the coupling at the manifold/feed-tube area per your model
• Inspect existing seals/O-rings and replace if worn
• Seat and lock the coupling fully; run a short cycle to check for leaks