Power Small Engine Regular Starter Parts
Genuine Lg part
By: Lg
Part Number: 6750C-0004R
The Compressor Overload Protector is an OEM replacement part for LG refrigerators. It plays an important safety role in protecting the compressor from damage due to excessive heat. Located near the compressor unit, the overload protector functions to shut off power to the compressor if temperatures become too high during operation.
Causes can include normal wear over time rendering it less responsive to temperature changes. Mineral or refrigerant deposits may also impede its ability to detect overheating conditions accurately.
Symptoms of a faulty overload protector include:
- Refrigerator fails to properly cool or the compressor does not run
- Circuit board or electrical component failure or burnout
- Lack of cold air production and higher than normal freezer/fridge temperatures
This OEM LG part is also compatible with some Sears/Kenmore models.
Do-It-Yourself Stories from Customers like You
Not cooling Paul B. • Frederick , MD • January 15, 2017
8 y/o LG unit was not cooling or freezing. There was a clicking on the back side every 2-3 minutes. Used these 2 issues in a internet search and top 2 cited problems were dirty coils then bad PTC & OLP. Tool off the back panel, compressor was quie hot. Coils did not look excessively dirty but cleaned them anyway. DId not resolve the problem. The OLP & PTC recommended for my unit. were different than the original TSD and I thought I would have to return the parts. However, I got on a chat...
Read more
More
$48.95
- Compare At:
-
$58.25
- You Save:
-
$9.30
Genuine Ge part
By: Ge
Part Number: WE1M1002
This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.
- Provides overcurrent protection for the circuit specified by the manufacturer
- If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
- Helps prevent wiring and component damage from shorts or overloads
- Repeated fuse failures indicate an underlying electrical issue requiring diagnosis
What's included: 1 CCMR fuse (30A, 120V) Install notes:
- Disconnect power to the appliance before servicing
- Locate the fuse in its holder/block and inspect associated wiring for heat or damage
- Test the old fuse for continuity; replace only with the identical rating specified
- Never bypass or upsize a fuse; correct the root cause of the failure before returning to service
Do-It-Yourself Stories from Customers like You
The dryer would not turn on Roland S. • Richmond , CA • August 02, 2014
First I check the breaker for the dryer then I check the power cord and the ohms to the power cord when all this things were in working order I then check the ohms to the fuse to the control panel.
The fuse had no ohms so I got a pair on needle nose pliers pulled out the fuse and replace it worked just find after that
Read more
More
$53.69
- Compare At:
-
$64.43
- You Save:
-
$10.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10131836
Fix dryer underheating or overheating issues with this 140°F fixed thermostat. Restores accurate temperature control and stops erratic cycling. Easy repair.
More
$69.95
- Compare At:
-
$82.54
- You Save:
-
$12.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10411937
Dryer won't start or run? A faulty belt switch often causes this when the belt snaps or slips. This switch monitors belt tension and is a fairly easy fix.
Do-It-Yourself Stories from Customers like You
Drum wouldnt turn power to control panel but wouldnt start Andy S. • Arlington , VA • November 03, 2016
Replaced motor "triple switch" Part Number: AP6021090 and the thermal fuse
Read more
More
$28.43
- Compare At:
-
$33.83
- You Save:
-
$5.40
Genuine Whirlpool part
By: Whirlpool
Part Number: WP31001590
Fix a dryer that won't heat or overheats with a new thermistor. This temperature sensor ensures accurate heating cycles. DIY repair in 30 minutes.
Do-It-Yourself Stories from Customers like You
Dryer ran but wouldn't heat the only thing i could find was the thremistor only real at 8 ohms instead of a little over 10 Ross M. • Ohiopyle , PA • October 24, 2016
Installed a new thermistor tempiture control and it heats up as it should.
Tools used was a ohlm meter, 1" stiff puty knife, #2 Philips screw driver, neadle nose pliers,1/4 & 5/16 nut drivers.
Read more
More
$59.48
- Compare At:
-
$70.78
- You Save:
-
$11.30
Genuine Whirlpool part
By: Whirlpool
Part Number: WP31001192
If your dryer is overheating, running too hot, or taking extended times to dry clothes, a faulty cycling thermostat is often the cause. Easy DIY fix.
Do-It-Yourself Stories from Customers like You
No heat on dryer low setting insufficient drying even on high extended times to dry Thomas M. • Galax , VA • June 12, 2016
Ended up replacing the cycling thermostat which corrected the problem. Andrew C. was very helpful with considerations and return of unneeded parts as well as very informative technical assistance. Could not have been treated better.
Read more
More
$79.24
- Compare At:
-
$93.50
- You Save:
-
$14.26
Genuine Frigidaire part
By: Frigidaire
Part Number: 131298300
Dryer won't heat or overheats? A failed cycling thermostat can't regulate temperature. This direct-fit part takes 15–30 minutes to replace.
Do-It-Yourself Stories from Customers like You
Rubbing blocks and felt that seal the front of the drum are worn drum is sagging and staining clothes with smears of rust Seth W. • Upper Arlington , OH • January 23, 2016
Replaced upper and lower felts. Painted rubbing surface on inside of drum with refrigerator enamel. Took out drum and lubed rear bearing. Replaced 2 of the 3 thermostats, and the belt just on principle.
Spent a lot of time with shop-vac removing lint from drier and exhaust ducts.
Runs great and is no longer cooking or staining clothes.
Read more
More
$52.76
- Compare At:
-
$62.78
- You Save:
-
$10.02
Genuine Whirlpool part
By: Whirlpool
Part Number: W10169881
Dryer not heating? A blown thermal cut-off is a common cause. This safety fuse opens if overheating occurs. Test with a multimeter for continuity.
Do-It-Yourself Stories from Customers like You
Dryer not heating (f31 error code Andrew D. • Kennewick , WA • April 17, 2015
Checked the heating element and found that it was shot so I bought a new one with out checking the thermostat and the cutoff-tml. I received the new element and it still wasn't heating so I had to wait another week for the cutoff-tml to be delivered. If your dryer isn't heating, make sure you check all parts of the heating system with a multimeter before you order new parts.
Read more
More
$73.95
- Compare At:
-
$88.00
- You Save:
-
$14.05
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10178809
Fix a dryer that won't heat or overheats with this cycling thermostat. Regulates heating element temperature for consistent drying. Simple DIY repair.
Do-It-Yourself Stories from Customers like You
Worn or broken thermostat. Nicholas R. • Canyon Lake , TX • March 14, 2024
It’s a simple fix. Unplug the wires and remove the two screws and replace it with the new one.
Read more
More
$58.43
- Compare At:
-
$69.53
- You Save:
-
$11.10
Genuine Lg part
By: Lg
Part Number: 6323EL2001C
This NTC thermistor is the dryer's temperature sensor. It monitors exhaust air temperature and signals the control to cycle the heat, restoring accurate drying performance and helping prevent overheating, underheating, and inconsistent results.
- Monitors exhaust air temperature by changing resistance as heat rises (NTC behavior)
- Sends temperature feedback to the control to regulate the heater or gas valve
- Failure can cause no heat, overheating, or erratic temperatures
- May lead to long dry times, short cycles, or temperature-related error codes
What's included: 1 thermistor Install notes:
- Disconnect power and, for gas models, shut off the gas supply before servicing
- Access the sensor on the blower housing or exhaust duct; location varies by model
- Note wire routing; unplug the harness connector; remove the mounting fastener/clip; install the new sensor fully seated and reconnect
- Reassemble, restore power, and run a test cycle; check and clean venting to ensure proper airflow
More
$31.32
- Compare At:
-
$37.27
- You Save:
-
$5.95
Genuine Whirlpool part
By: Whirlpool
Part Number: W11165163
The Electrode is an OEM replacement part for Whirlpool dryers. It is responsible for detecting the moisture levels in your laundry during the drying cycle, allowing the dryer to automatically adjust the drying time and temperature. It helps prevent over-drying or under-drying of your clothes, saving energy and protecting them from potential damage.
A bad electrode can occur due to wear and tear, damage, or a buildup of debris or lint. If you notice symptoms such as clothes taking longer to dry, the dryer shutting off prematurely, or inconsistent drying results, it may be time to replace the moisture sensor bar electrode.
Symptoms of a bad electrode include:
- Clothes taking longer to dry than usual
- The dryer shutting off prematurely
- Inconsistent drying results, with some items remaining damp
Repair your dryer by replacing the faulty or damaged electrode with this genuine OEM part.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
More
$50.57
- Compare At:
-
$59.67
- You Save:
-
$9.10
Genuine Ge part
By: Ge
Part Number: WR08X10112
Fix compressor clicking every few minutes or fridge not cooling. This start relay and overload combo helps your compressor start and prevents overheating. Easy 5-minute fix.
Do-It-Yourself Stories from Customers like You
Constant clicking sound from behind refrigerator and compressor would not kick on all the time freezer temp was above the desired temperature Peter H. • Bayside , NY • May 10, 2016
I replaced the old capacitor and combo device after watching repair video. Took less than 5 minutes and now my ge profile refrigerator is running perfectly.
Read more
More
$108.30
- Compare At:
-
$128.88
- You Save:
-
$20.58
Genuine Ge part
By: Ge
Part Number: WE4M411
Dryer won't heat or overheating? The temperature switch controls heat settings. DIY-friendly repair—just swap wires and reassemble. Takes 20 minutes.
Do-It-Yourself Stories from Customers like You
The timer was sticking to the point where the knobs were stripping out Peter A. • Dallas , OR • December 16, 2014
I unscrewed the 3 Phillips screws on the back of the dryer controls housing, then it folds forward for access to each control switch. the old one popped out, and I swapped the wires using a needle nose pliers, one by one, from the old switch to the new switch. The part was an exact fit, and popped right back into the housing. I screwed the 3 screws back in, pushed on the new knob, and it looks and works like new !
Read more
More
$64.70
- Compare At:
-
$76.99
- You Save:
-
$12.29
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3399640
Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.
Do-It-Yourself Stories from Customers like You
The temperature switch did not engage Peter K. • Highland Hts. , OH • December 27, 2022
Replaced the Temperature Switch
Read more
More
$62.61
- Compare At:
-
$74.51
- You Save:
-
$11.90
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8566498
Dryer not heating or taking too long to dry? This high-limit thermostat monitors temperature and cuts power when it gets too hot. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Dryer not heating Jeffrey F. • Apex , NC • September 16, 2017
Our dryer seemed to be taking a long time to dry, often needing a couple cycles to complete the job. Then one day it stopped heating at all. After watching a couple videos and testing with a multimeter I figured out not only the thermristor had blown (can happen due to bad airflow) but also half the heating element was shot. I ordered both parts for overnight delivery and received them at noon the next day. Replacement was easy and the dryer is good again.
Side note: After the repair was...
Read more
More
$51.62
- Compare At:
-
$61.43
- You Save:
-
$9.81
Genuine Whirlpool part
By: Whirlpool
Part Number: 279872
This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.
- Provides precise resistance to reduce voltage/current in the designated dryer circuit
- Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
- Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
- Replace if visibly burned/damaged or if testing shows an open or shorted condition
What's included: One resistor Install notes:
- Disconnect power to the appliance before servicing
- Access the console/wiring harness and note original wire routing
- Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
- After installation, run a test cycle to ensure proper operation of the affected function
Do-It-Yourself Stories from Customers like You
Timer wouldn't advance on my dryer John L. • Oblong , IL • March 22, 2016
I ordered a new timer and installed it with the help of the videos provided and this did not solve my problem so I chated with the pros @ Appliance Parts Pros and told them my problem and they told me the problem and recommended the part I needed and With the incredibly fast shipping I had the part the next day. I installed it and now my dryer timer works great.Thanks to APPs for their help and ease of ordering and fast shipping. I highly recommend AppliancePartPros and will definitely use...
Read more
More
$46.35
- Compare At:
-
$54.69
- You Save:
-
$8.34