Turn Power Small Engine Regular Starter Parts

Fix dryer heating issues with this thermistor temperature sensor. Solves intermittent heat, cycle errors, and poor drying. Easy DIY repair.

Dryer won't heat or overheats? A failed cycling thermostat can't regulate temperature. This direct-fit part takes 15–30 minutes to replace.

The Compressor Overload Protector is an OEM replacement part for LG refrigerators. It plays an important safety role in protecting the compressor from damage due to excessive heat. Located near the compressor unit, the overload protector functions to shut off power to the compressor if temperatures become too high during operation.

Causes can include normal wear over time rendering it less responsive to temperature changes. Mineral or refrigerant deposits may also impede its ability to detect overheating conditions accurately.

Symptoms of a faulty overload protector include:

• Refrigerator fails to properly cool or the compressor does not run
• Circuit board or electrical component failure or burnout
• Lack of cold air production and higher than normal freezer/fridge temperatures

This OEM LG part is also compatible with some Sears/Kenmore models.

This replacement switch restores reliable on/off signaling to the circuit it controls, helping your appliance start, stop, and respond correctly. A worn switch can cause intermittent operation, no response, or lights and functions that don't activate. What it does:

• Provides an electrical open/closed signal to enable functions like starting a cycle, powering a motor or light, or shutting a feature off
• Acts as a safety/position interlock (such as door, lid, float, or hood) depending on the model
• Typical symptoms include won't start, won't stop, light won't turn on/off, or intermittent operation
• Can be checked with a multimeter for continuity when actuated

• 1 switch

• Disconnect power before servicing; turn off gas or water supply if applicable
• Access the switch, note wire locations, and transfer leads one at a time to the new switch
• Mount securely, ensure the actuator aligns and wires aren't pinched
• Reassemble and test operation before finalizing

If your dryer is overheating, running too hot, or taking extended times to dry clothes, a faulty cycling thermostat is often the cause. Easy DIY fix.

Fix a dryer that won't heat or overheats with a new thermistor. This temperature sensor ensures accurate heating cycles. DIY repair in 30 minutes.

Fix dryer underheating or overheating issues with this 140°F fixed thermostat. Restores accurate temperature control and stops erratic cycling. Easy repair.

Dryer won't start or run? A faulty belt switch often causes this when the belt snaps or slips. This switch monitors belt tension and is a fairly easy fix.

This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.

• Provides overcurrent protection for the circuit specified by the manufacturer
• If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
• Helps prevent wiring and component damage from shorts or overloads
• Repeated fuse failures indicate an underlying electrical issue requiring diagnosis

• Disconnect power to the appliance before servicing
• Locate the fuse in its holder/block and inspect associated wiring for heat or damage
• Test the old fuse for continuity; replace only with the identical rating specified
• Never bypass or upsize a fuse; correct the root cause of the failure before returning to service

Dryer not heating? A blown thermal cut-off is a common cause. This safety fuse opens if overheating occurs. Test with a multimeter for continuity.

Fix a dryer that won't heat or overheats with this cycling thermostat. Regulates heating element temperature for consistent drying. Simple DIY repair.

This NTC thermistor is the dryer's temperature sensor. It monitors exhaust air temperature and signals the control to cycle the heat, restoring accurate drying performance and helping prevent overheating, underheating, and inconsistent results.

• Monitors exhaust air temperature by changing resistance as heat rises (NTC behavior)
• Sends temperature feedback to the control to regulate the heater or gas valve
• Failure can cause no heat, overheating, or erratic temperatures
• May lead to long dry times, short cycles, or temperature-related error codes

• Disconnect power and, for gas models, shut off the gas supply before servicing
• Access the sensor on the blower housing or exhaust duct; location varies by model
• Note wire routing; unplug the harness connector; remove the mounting fastener/clip; install the new sensor fully seated and reconnect
• Reassemble, restore power, and run a test cycle; check and clean venting to ensure proper airflow

Fix compressor clicking every few minutes or fridge not cooling. This start relay and overload combo helps your compressor start and prevents overheating. Easy 5-minute fix.

The Electrode is an OEM replacement part for Whirlpool dryers. It is responsible for detecting the moisture levels in your laundry during the drying cycle, allowing the dryer to automatically adjust the drying time and temperature. It helps prevent over-drying or under-drying of your clothes, saving energy and protecting them from potential damage.

A bad electrode can occur due to wear and tear, damage, or a buildup of debris or lint. If you notice symptoms such as clothes taking longer to dry, the dryer shutting off prematurely, or inconsistent drying results, it may be time to replace the moisture sensor bar electrode.

Symptoms of a bad electrode include:

• Clothes taking longer to dry than usual
• The dryer shutting off prematurely
• Inconsistent drying results, with some items remaining damp

Repair your dryer by replacing the faulty or damaged electrode with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.

Dryer not heating or taking too long to dry? This high-limit thermostat monitors temperature and cuts power when it gets too hot. DIY-friendly repair.