Circuit Board Parts

This dryer timer controls cycle length and sequencing, advancing the machine through the selected settings and turning it off at the end. Replacing a failed timer restores proper cycle timing, advancing, and dependable automatic shutoff.

• Controls cycle timing and the order of operations throughout the selected program
• Routes power to the motor and other circuits as the internal cam advances
• Advances through timed and automatic cycles to complete the load
• Common symptoms of a failed timer: cycle won't advance, dryer runs too long or won't shut off, won't start or only works on one setting, stops mid-cycle

• Disconnect power; for gas dryers, also turn off the gas supply
• Access the control console; remove the old timer from its mounting and note wire locations
• Photograph wiring and transfer leads to the same labeled terminals one at a time
• Reassemble the console, restore power, and test that all cycle positions advance and shut off properly

This is a control panel that is used on many ovens. It is an interior part located near the buttons a user can press to turn on the oven, change the temperature, and select cooking methods. The control panel is the component that controls the oven based on which buttons are pressed. It includes a small display screen that shows the temperature, time, or error codes if a part of the appliance is not working correctly.It's important to be sure the range is unplugged before replacing the control panel. A Phillips screwdriver can unthread the screws holding the rear access panel. Pull the panel down and note where the wires are connected to the damaged control panel. Remove the old control panel and position the new one before securing it with screws. Replace the wires on the correct terminals before tightening the screws and replacing the access panel. Turn back on the power and push back the oven before use.This is a genuine OEM replacement control panel used for a variety of Whirlpool ovens. It is sold on an individual basis. A pair of work gloves and basic tools may be required for the replacement process.

The Control Board is an OEM part for Whirlpool dishwashers. It serves as the brain of the appliance, controlling and regulating all functions and cycles of the dishwasher.

Causes of a bad Control Board can range from power surges or electrical issues that damage the board's components, to physical damage from moisture exposure or impact, as well as general wear and tear over time.

Symptoms of a faulty dishwasher Control Board include:

• The dishwasher not turning on or starting cycles
• Certain wash cycles or options not functioning correctly
• Error codes or indicator lights displaying on the control panel
• The dishwasher shutting off unexpectedly during cycles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Adaptive Defrost Control Board

The Control Board is an OEM part for Frigidaire ranges. This part controls the oven functions, including temperature regulation, cooking modes, and timer settings.

Causes of a bad control board can include electrical surges, moisture damage, excessive heat, or general wear and tear.

Symptoms of a bad range control board include:

• The oven or burners not turning on
• Unresponsive or malfunctioning control panel
• Incorrect temperature settings
• Error codes displayed on the control panel
• Oven not maintaining set temperature

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Noise Filter Assembly is an OEM part for LG dishwashers. It is designed to reduce electrical noise and interference that can affect the dishwasher's operation. The noise filter helps ensure that the electronic components function smoothly and without disruption, contributing to the overall efficiency and reliability of the appliance.

Causes of a bad noise filter assembly can include electrical surges, wear and tear over time, or damage due to moisture or physical impact.  

Symptoms of a bad noise filter assembly include:

• The dishwasher not starting or stopping unexpectedly
• Error codes related to electrical issues
• Intermittent power loss during a cycle
• Unusual noises coming from the control panel area

This OEM LG part is also compatible with some Kenmore models.

This dishwasher main control board kit is the central circuit board that directs all wash functions. Replacing a failed board restores proper power distribution and timing so cycles start, advance, and finish correctly, helping prevent intermittent shutdowns and erratic operation. What it does:

• Controls cycle timing and communicates with sensors
• Distributes power to the wash motor, drain pump, inlet valve, and heater
• Works with the door latch and user interface to start/stop the cycle
• Failure may cause no power/won't start, stalled cycles, blinking lights/error codes, or incorrect filling, draining, or heating

• One main control board kit

• Disconnect power at the circuit breaker; turn off water if moving the dishwasher for access
• Board is typically in a housing beneath the unit—use ESD precautions and keep connections dry
• Photograph/label wire harnesses; transfer connectors one at a time to the new board
• Restore power and run a test or rinse cycle to proper operation

This washer timer controls the sequence and duration of wash, rinse, drain, and spin cycles. Replacing a worn timer restores proper cycle advancement and consistent performance when the machine stalls, skips steps, or runs unpredictably.

• Sequences power to the motor, pump, and water valves to run each stage of the cycle
• Advances through timed contacts to start and stop functions at the right time
• Common symptoms: cycle won't advance or stops mid-cycle; washer won't start
• Runs too long or too short; skips or repeats steps
• No drain or spin; timer knob doesn't move or shaft slips

• Disconnect power before servicing; turn off water if moving the appliance
• Open the control console to access the timer; remove rear cover as needed
• Note wire positions; transfer connectors one at a time or photograph for reference
• Secure the new timer, reinstall dial/knob if applicable, reassemble, and test a full cycle

This is the electronic oven control board that manages bake and broil temperatures, oven timing, and display functions. Replacing a failed control restores accurate temperature regulation and front-panel responsiveness so your range can cook reliably again.

• Regulates oven temperature by cycling bake/broil elements per setpoint
• Controls oven timing functions and user interface/display
• Common failure signs: unresponsive buttons, error codes, inaccurate temps, no heat, or blank/erratic display
• Designed for direct replacement of the original factory control

• Disconnect power at the breaker before servicing
• Transfer overlay and wiring from the old board to the new one, noting connector positions
• Handle the PCB carefully to avoid static discharge and damage
• After installation, run a test bake cycle

This electronic oven control board manages oven heating functions and the display on gas ranges. Replacing a failed board restores reliable ignition, accurate temperature control, and normal bake/broil operation.

• Regulates oven temperature by reading the sensor and cycling the gas burner through the bake/broil relays
• Drives the clock and function display
• Interprets keypad inputs to select modes and temperatures
• Common failure signs: oven won't heat or maintain temperature, blank or erratic display, unresponsive controls, or recurring fault alerts

• Disconnect power at the breaker and shut off gas before servicing
• Use ESD protection and handle the board by the edges
• Photograph wiring and transfer connectors one at a time; reinstall using existing hardware
• Some models require transferring the original keypad/overlay to the new board

The Main Control Board Kit is an OEM part for GE dishwashers. This electronic control board manages various dishwasher functions, including water intake, temperature settings, wash cycles, and drying times. It's the brain behind the efficient operation of your dishwasher, ensuring that all components work in harmony for optimal cleaning results.

The primary causes of control board failure often involve power surges, moisture damage, or component wear and tear, which can disrupt the electrical pathways and circuits within the board.  

Symptoms of a bad Main Control Board include:

• Dishwasher failing to start or stopping mid-cycle
• Unusual error codes displayed on the dishwasher panel
• Non-responsive controls or settings that don’t change appropriately

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Timer is an OEM part for GE washing machines. This part controls the various cycles of the washing machine, including wash, rinse, and spin, by regulating the duration and sequence of operations.

Causes of a bad timer can include wear and tear over time, electrical issues such as short circuits or power surges, and mechanical failures within the timer mechanism.

Symptoms of a bad timer include:

• The washing machine not advancing through cycles
• The machine stopping mid-cycle
• Inconsistent or incorrect cycle durations
• The machine not starting at all

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Electronic Control Board is an OEM replacement part for Frigidaire freezers. It functions to operate all freezer systems and components through electronic programming and input received from sensors. 

Causes of a failed control board can include moisture damage impairing circuitry over time, power surges disrupting electronics, or logic and memory failures.

Symptoms of a problematic control include:

• The freezer failing to cool or freeze properly
• Lights or other features not functioning as expected
• Error codes appearing regarding control faults  
• Sensors and components not responding to control signals

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This OEM replacement part is a relay control board for ovens. The relay control board receives signals from the main oven control board. This part regulates the oven's temperature. If the oven is no longer heating properly or maintaining temperature it might be time to replace the relay control board. Luckily replacing this board is an easy repair. To replace the relay control board, begin by turning off all power to the oven. Once the power has been shut, move the oven away from the wall to gain access to the upper back panel. Remove the panel and locate the relay control board. Snap it out of its mounting brackets and remove the wire harness connected to it. Reinsert the wire connectors to the new relay board in the correct order. Secure the new board into its mounting brackets. Reinstall the upper back panel.This genuine replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This electronic oven control board is the brain of your range or wall oven. Replacing a failed board restores the display and keypad response and allows the appliance to heat and run bake/broil cycles reliably again.

• Controls relays for bake and broil circuits
• Uses oven sensor feedback to regulate and maintain temperature
• Powers the time/temperature display and reads keypad inputs
• Common symptoms: blank or erratic display, unresponsive buttons, F-code errors, oven won't heat or shuts off mid-cycle

• Disconnect power at the breaker before servicing; allow the appliance to cool
• Static-sensitive component—handle by the edges and avoid touching circuitry
• Note/photograph wire locations; transfer connectors one at a time to the new board
• Mount the board in the control panel, secure connections, restore power, and test

This is the electronic control board for the oven. It manages heating functions and the display so the appliance heats accurately and responds to your selections as designed.

• Regulates power to bake and broil elements to reach and hold set temperatures
• Processes input from the oven sensor and user keypad/display
• Controls timers, clock, and on-screen status or fault indications
• Common failure symptoms include no heat, oven won't start, erratic/blank display, or recurring fault codes

• Disconnect power at the breaker before servicing; high voltage is present
• Use ESD precautions; handle the board by the edges only
• Note wire locations or take photos; move connectors one at a time to the new board
• After installation, restore power, set the clock, and test bake and broil functions