Turn Tip Small Engine Ignition Coil Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10275049
Burner not heating or heating unevenly? This dual radiant surface element restores consistent heat to both rings. DIY-friendly, installs in 15 minutes.
Do-It-Yourself Stories from Customers like You
Whirlpool glass top burner replacement James F. • Fort Lauderdale , FL • March 21, 2015
It was a simple process to enter the model number of our glass cook top stove; learn the part number required and order. It arrived in 2-days -- least expensive shipping method.
The cooktop was removed with a Phillips-head screwdriver by 4 small sheet metal screws on the right and left side of the oven.
The oven's power to the cooktop was easily disconnected via two "clips" and one ground.
Would have cost way more with an appliance repair shop and it's an easy do-it-yourself repair.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY04100020
Oven not heating or baking unevenly? A failed bake element is likely the cause. This repair takes just 5-10 minutes with basic tools and no special skills.
This part fixes the following symptoms
-
Element will not heat
-
Little to no heat when baking
-
Oven not heating evenly
See more...
Do-It-Yourself Stories from Customers like You
Oven on longer working found a hole blown through the ceramic covering in the bake element meaning that the heating wire had burnt off William N. • Canandaigua , NY • July 19, 2014
Removed 2 sheet metal screw pulled element out about 2 inches. Removed two Spade connections. Removed the element from the oven.
Inserted the new element into the over, connected the two spade connector. Reinstalled the two sheet metal screws. Set the oven to bake for testing and tested until the element turned red.
Total time less than 5 minutes.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303937186
The Ignitor Assembly is an OEM replacement part for Frigidaire dryers. It serves as the ignition source safely firing up burners to initiate drying cycles.
Causes usually relate to the continual thermal shock experienced from heating and then rapidly cooling over extended use. As a foundational safeguard, ignitors require OEM replacement when arcing declines.
Symptoms of a faulty ignitor can include:
- The dryer fails to start or stop heating intermittently
- Cycles taking overly long to complete or feel uneven
- Excessive service calls relating to "no heat" troubles
- Risk of uncombusted gas pooling in dryer if ignition falters
This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
This part fixes the following symptoms
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Gas smell in the dryer after a cycle completed no smell outside the dryer (until i opened the door!) Matthew M. • Mcfarland , WI • April 25, 2016
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP15418
Converting dryer from LP to natural gas? This gas orifice regulates gas flow to the burner for proper heating. DIY-friendly swap, takes 20 minutes.
Do-It-Yourself Stories from Customers like You
I needed to convert from lp to natural gas Mark S. • Raleigh , NC • June 01, 2015
Removed LP Orifice and LP Gas limiter.
Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP.
I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693140
If your dryer won't heat or flame won't stay lit, a corroded burner tube may be the cause. This assembly includes an adjustable air shutter for proper combustion.
Do-It-Yourself Stories from Customers like You
Dryer not heating Ray M. • Marissa , IL • October 03, 2014
I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY04000048
The Broil Element is an OEM part for Whirlpool ranges. This part provides the intense, direct heat necessary for broiling. This part is located at the top of the oven cavity and is essential for achieving high temperatures needed for tasks like browning and searing.
Causes of a bad broil element can include electrical issues such as short circuits, damage from spills or food debris, and general wear and tear from repeated use.
Symptoms of a bad Broil Element include:
- The oven not reaching broil temperatures
- Inconsistent or uneven broiling
- The element not glowing red when in use
- Visible signs of damage or burning on the element
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
This part fixes the following symptoms
-
Little to no heat when broiling
-
Element will not heat
See more...
Do-It-Yourself Stories from Customers like You
Broil element was burned out Aybars G. • Ridgewood , NJ • June 17, 2019
Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on.
Hardest part was loosening...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W11628765
Oven not heating or taking too long to preheat? This bake element installs at the bottom of the cavity to restore consistent heat and proper baking.
More
Genuine Ge part
By: Ge
Part Number: WE4M449
If your dryer won't heat or takes too long to dry, a faulty gas igniter is often the cause. This assembly heats up to ignite the burner for proper drying.
Do-It-Yourself Stories from Customers like You
Would not ignite gas burner consistentlyi John M. • O'fallon , MO • October 17, 2016
Installed a new igniter.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303918208
Fixes ice buildup on evaporator coils and warm fridge temps. This defrost heater kit melts frost during the defrost cycle. Moderate DIY repair with video.
Do-It-Yourself Stories from Customers like You
This was for a friend of mine his refrigerator stopped cooling Gary G. • Ofallon , MO • July 12, 2015
This was a 2000 model so rather than just replace the defrost timer which was visibly burnt on the terminals, we just did everything. The cold control, defrost timer, thermostat, defrost heater and the compressor capacitor were all replaced. I had the same issue on my older unit and tore it apart replacing one item at a time over a three month period so on an older one i suggest do it all while it is apart.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304516159
Element not heating? This surface element is the most common fix. Compatible with Frigidaire electric ranges. Tests between 15-45 ohms resistance.
Do-It-Yourself Stories from Customers like You
2 elements were inop problem resolved by replacing with new ones phone tech was very helpful John N. • Southbury , CT • June 28, 2026
Se above
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10825088
This defrost heater is mounted near the evaporator coils and generates heat to melt frost buildup during the automatic defrost cycle. It helps maintain proper airflow and cooling efficiency inside the refrigerator. Replace this heater if you notice excessive frost on the evaporator coils, the refrigerator is not cooling properly, or the freezer section is warm.
Do-It-Yourself Stories from Customers like You
Malfunctioning defrost heater Robert R. • Asheville , NC • March 11, 2015
Total repair took slightly over 1 hour. Would have taken longer had I not already have taken the freezer apart on a previous occasion. Therefore I already knew the sequence and was able to disassemble it quickly. A little tricky getting the part out but easier to get it in. SImple repair for anyone mechanically inclined.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB44T10031
Oven not heating or baking unevenly? A faulty bake element is often the cause. This bottom heating element is straightforward to replace yourself.
This part fixes the following symptoms
-
Little to no heat when baking
See more...
Do-It-Yourself Stories from Customers like You
The boil and baking elements Raymond S. • Dealeton , VA • September 26, 2019
I just took them off and replaced them.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10583047
Broiler won't heat or element burned out? This upper broil element restores intense top-down heat for even browning. DIY-friendly repair in under an hour.
This part fixes the following symptoms
-
Little to no heat when broiling
See more...
Do-It-Yourself Stories from Customers like You
The self cleaning feature of my ge double oven hasn't worked in years and recently the upper oven baking element stopped working Robert A. • Enfield , CT • October 19, 2015
I wanted to get the upper oven baking element replaced; it hasn't been working for a few months. This double oven has had two other issues, there is a fan that comes on to cool the electronics panel, That fan has made excessive noise and it operates for 2-3 hours after the oven turns off. The other problem with the oven is the Self-Cleaning feature runs for about 15-30 minutes and then turns off with an error code. I've had a local appliance repair person in to address the error code and...
Read more
More
Genuine Samsung part
By: Samsung
Part Number: DG47-00060A
Burner not heating or shorted out? This radiant heating element restores cooktop performance. DIY-friendly repair, typically takes 20 minutes to install.
Do-It-Yourself Stories from Customers like You
Burned out element Michael R. • Jacksonville , FL • October 30, 2015
Removed the top of the range after unplugging it, removed the brace holding the element, replaced the element. Total of 20 minutes spent.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB30X254
Burner not heating or heating unevenly? This 6-inch surface coil element restores consistent heat to your range's small burner. Simple plug-in install.
Do-It-Yourself Stories from Customers like You
Needed new heating coils Judith C. • Stanhope , NJ • February 22, 2016
Ordered new heating coils for stove
Read more
More
Genuine Ge part
By: Ge
Part Number: WB44X48671
This bake element heats the oven cavity for standard baking operations, restoring even heat when the original element fails. It installs at the rear or bottom of the oven cavity to provide the radiant heat needed for baking. What it does:
- Heats the oven cavity to maintain proper baking temperatures.
- Replaces a burned, broken, or visibly damaged element that won't glow or heat.
- Helps correct symptoms like insufficient heat, uneven baking, or an oven that won't reach set temperature.
- Works with the oven's control system and thermostat to deliver steady radiant heat.
What's included: One bake element. Install notes:
- Disconnect power to the appliance before starting — turn off the circuit breaker or unplug the range.
- Allow the oven and old element to fully cool before handling.
- Handle the element carefully to avoid bending or damaging the terminals or ceramic insulators.
- After installation, restore power and test the oven on a bake cycle to ensure the element heats correctly.
Do-It-Yourself Stories from Customers like You
Bottom bake element for the top oven had to be replaced Lois S. • Christiana , TN • January 08, 2021
Ordered new bake element on 01/03/2021 and received on 01/05/2021. Thanks for the expedited service. My husband removed the old bake element and replaced with the new bake element. Took less than 15 minutes to remove and replace.
Read more
More