Float Switch Float Parts

Replaced dual element switch. Fixed the problem. All is good Read more

Initially performed troubleshooting over the phone with Bosch customer support and did preliminary research on the web. Ultimately had to call out service technician to isolate/confirm problem. He confirmed the problem was most likely the switch (if not, the actually computer processor) and gave me the part number (since it was going to take 10 BD's for him to get the part). I ordered through Appliance Parts Pros and received the part in only 2 days. However, upon trying to install it, I... Read more

This was a very simple repair. It was done in about an hour. It involves disconnecting the dishwasher, emptying the water from the inside, taking it out and flipping it over, and replacing the diverter motor. This repair is done on the underside of the dishwasher, nothing to disconnect inside (just remember to remove the baskets). It would be wise to order the motor seal and micro switch that goes with it as they are all cheap parts and easy to swap out during the procedure. Be sure to take... Read more

• Won't start

Bought this switch gas valve for the non-functional burner, and it cleared right up. Read more

• Will not drain

I checked the drain hose for blocking at the garbage disposal and then at the connection point to the dishwasher. The hose was clear and nothing was obviously obstructing where the drain hose connects to the dishwasher. At this point I Googled the model number with the term "will not drain" and immediately landed on the AppliancePartsPros.com website. At the Drain & Wash Impeller Kit page amazingly had a video showing the technician replacing the impeller on a dishwasher essentially the same as... Read more

Part easily replaced and problem was solved. Saved service call. Read more

Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,... Read more

Ordered the right part, took the back off the top control panel, and popped it in. Read more

• Will not stop filling with water
• Will not fill with water

I took the washer apart and replaced the water level switch and hose with new ones. I followed the video that I found on youtube (which is on the site) and had no problems at all. Read more

Searched internet for answers. Decided to replace the door switch. Drier now runs great! Read more

So I ordered the burner and Ithe switch because I wasn't sure what part was defective. I pulled the oven out and I removed the 6 1/4 inch screws on each side of the glass top as well as the 2 Phillips head screws on the back, removing the 2 1/4 screws on the shield on the back gIves you easier access to them, then lifted the glass top up on the front to access the switch and burners. Make sure you turn the power off before beginning this process. When lifted up the wires connected to the... Read more

• Won't start

1) Ordered part. 2) Removed front panel by loosening the two screws at the bottom front. 3) Removed old Safety Switch/Lid Lock by disconnecting wires (plug and 2 female disconnects) 4) Reconnected all wires and reinstalled switch. 5) Replaced front panel. 6) Tested Unit. 7) FYI - I found that the locking mechanism stays locked until cycle completely finishes on its own. DO NOT force the cycle to end. Lid will NOT unlock. Read more

I purchased 2 new light rocker switches, Because the heating element rocker switch was unavailable. First I removed the power source for safety. Then I simply pulled each switch out individually with a flathead screwdriver for leverage. I simply unplugged the wires from the old rocker switch, discarded the old rocker, plugged the wires into the new rocker switch, and pushed the new switch appropriately back into the control panel. I used the same steps for both rocker switches. Once... Read more

• No hot or cold water

I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me.. Read more

Watched your video and replaced the switch Read more