Need Help?
Call
The Rocker Switch is an OEM part for GE ranges. This switch is used to control the surface heating elements, allowing users to turn them on or off and adjust the heat levels. It is designed to fit securely into the range's control panel, providing reliable operation and ease of use.
Causes of a bad switch rocker element can include regular wear and tear, electrical issues, or damage from spills or high temperatures. Over time, the internal contacts of the switch can degrade, leading to malfunction.
Symptoms of a bad switch rocker element include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Replaced the switch took a total of about five minutes. I pulled the stove out and turned the breaker off so I only had to pull it out enough to get a 1/4 " nut driver in behind it. Removed three screws and the back cover came off. I pushed the switch threw from the back and switched over the two wires then reversed the process. Completely easy if you can use a screw driver your crazy not to replace it yourself Read more
Burner won't regulate heat or stays on constantly? The infinite switch controls burner temperature settings. Most DIYers replace it in 15-20 minutes.
Replaced the control that I think was bad from the purchase of the stove new as the burner didn’t throttle as is does now. Read more
If your cooktop burner is stuck on high or won't adjust temperature, the infinite control switch likely failed. This part controls heat levels.
The parts are under the stovetop and the knobs are attached to them. We bought the correct ones from AppliancePartsPros, these were the correct ones. Seems we have an oddball stovetop. It's a GE drop in stove. The parts were easy to change. It was a simple matter of putting the wires on the new switch in the same place there were on the switch. I took phone pics of the wire locations before I took them off and only did one switch at a time. Turn the power off at the breaker panel first of... Read more
Fixes refrigerator not cooling with hum-click sound from compressor. This PTC start device energizes the compressor start winding. DIY repair in 10 minutes.
New start device. Read more
Microwave won't start or runs only when door is pulled? Replace faulty door interlock switches. This 2-pack covers top and bottom switches. DIY repair.
First, it was going to cost $95 for an appliance guy just to look at it! I figured there would be an upcharge on the parts + labor on top of the $95, so I took a chance & decided my husband & I could fix it cheaper; we were right, but it was a 3 week process (luckily, we have another microwave in the basement we were able to use in the meantime). I googled the microwave model #, then price checked the same item I thought we needed; printed off the diagrams of the various microwave "systems" &... Read more
This 3-position fabric selector switch is the control behind the knob that lets you choose the fabric setting on your unit. Replacing a worn switch restores positive detents and ensures your selection is recognized instead of ignored or stuck.
Replaced the fabric selector switch. Took abut fifteen minutes. Dryer works fine. Read more
Dryer won't start or tumble? This belt switch monitors drive belt tension and cuts power if the belt breaks or slips. Moderate DIY repair with video.
Remove bottom panel, remove top panel, remove drum. Had to cut old squirrel cage off. Remove motor to remove old wheel shank. Remove belt switch, and replaced. Videos from AppliancePartPros helped a lot.. Read more
Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.
I went on your website found the parts needed to make the repairs. I watched the short video on installation. The parts arrived just a few days after I placed the order. I finished the repair in less than an hour and had to wait a few minutes to test the switch since the power was off and on due to a wind storm. Simple easy to do repair and I saved $90.00 on service fee for a tech to do the repair. Read more
Fixes burner stuck on high or no heat issues. This infinite switch regulates cooktop element temperature by cycling power on and off. Simple replacement.
Just a simple install my maintenance man just put it in with no problems. Read more
Ice maker not harvesting or making ice? This rocker switch controls ice maker operation. Common fix when ice production stops despite good water flow.
Fix a washer stuck mid-cycle or showing overfill errors with a new water level pressure switch. This part detects water levels to control fill cycles.
Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub. Read more
Compressor won't start or cycles on and off every few minutes? This overload relay protects against overheating. DIY repair in about 10 minutes.
The compressor was very hot and did not appear to be running. You could here a relay click on and off 15sec cycle. repeating every 2 minutes! Bought a new overload relay too repair, plus a new thermal protection switch because it was cheap. Both parts are actually located on the compressor behind a plastic cover. Found part numbers for parts by searching the compressor number on google! $25 Repair............ Read more
Fix a washer that won't agitate or spin with this lid switch. This safety part detects if the lid is closed. Easy DIY repair with basic tools.
Replaced lid switch and capacitor Read more
Washer won't start or fill with water? A faulty lid switch assembly with fuse is often the cause. DIY-friendly repair—most complete it in under an hour.
Removed front and top panels of washer, removed old switch assembly. Then mounted and hooked up new switch assembly, put panels back on, turned on power and unit now works fine. Thanks for the quick delivery on the part...our total machine down time was only 36 hours. Biggest difficulty was getting the machine out of its position to work on it! Read more
This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:
The Dual Element Surface Switch is an OEM part for Frigidaire electric ranges and cooktops. It governs power distribution to the dual element.
Causes may be loose electrical terminals within the switch, defects from past power surges, or general wear over extended use.
Symptoms of a bad surface switch include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
I replaced both the large single element and the large dual element control switches. It appears the resistors were burning out. Problem seems to be fixed. Will know later when I do some simmering. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.