Spitfire Control Parts

Replaced timer. Took 15 minutes Read more

I replaced the control board. Repair company wanted $395.00. I ordered the board for 140ish, 5 days later, 9 screws, 6 moduler plugs....working oven. The hardest part was pulling out the stove. Read more

Checked circuit breaker to d/w first. Good. Went to website to see no power issues. Most all of them mentioned the noise filter being the problem. Removed filter from machine and found the corner melted where fuse is located. Ordered new filter, installed, and now have power to switches. All the information I found on the website really made this a easy job to get done. Read more

• Timer will not advance

Just as the folks in the comments section said, I tested everything to make sure the timer had power which it did. I then tested with the OHM tester and saw that the switch was open when the timer was set to any drying cycle. So i changed the timer and voila! timer is functioning again. It was a very easy fix. Just pop the four screws out of the back of my timer panel on the dryer, detach all the wires, lift up on the little bracket that is holding the timer in place and twist it, and it... Read more

After unplugging the washer from the electrical outlet, the top of the washer was removed without a problem in order to allow easy access to the Central Control Unit (CCU) at the top of the back end of the washer. A cell phone was used to photograph the wiring layout and connectors plugged into the CCU, and then all connectors and the harness were carefully removed from the CCU without incident. Attempting to remove the old CCU, the plastic retaining clips built into the old CCU housing broke... Read more

Bought the circuit board you recommended and it fixed it perfectly Read more

Replaced Main PCB Assy. Read more

Replace the inverter and pc board noticed the pc board had a bulging capacitor so replaced it while I was at it. Both were simple fixes. Taking less than 45 total. Read more

I called a local appliance service person, who diagnosed the problem as a bad main power board and offered to fix it for a substantial sum. I found the part on Appliance Parts Pros and found it on my doorstep 2 days later (even though I only used the standard shipping option). Although Appliance Parts Pros did not have any instructions about how to install the part, I found a youtube video by ApplianceVideo.com that explained the procedure in sufficient detail. The entire repair start to... Read more

Got help from the internet to diagnose the problem. Seens that the neutral drain part of the transmission will not shift to spin unless there is a pause after draining. Thought the problem might be in the transmission but found the timer wasn;t allowing a pause after draining.therefore the machine would not spin. Replaced the timer and problem was solved. Thanks for your help, Jerry w. Read more

Tested start relay and fan with multimeter both passed. The condenser would start only if the thermostat was on the highest setting and the refrigerator would cool for a while, stop and not restart unless I adjusted the defrost timer. Decided to replace the thermostat, defrost timer and defrost thermostat. The refrigerator is working as expected. FYI on a Kenmore 59669142992 the defrost timer is located under the freezer in the front right. Read more

My dishwasher just stopped working one day. I know my way around tools but wouldn’t call myself a “handyman“. When I opened up the front panel on the dishwasher I saw that the Control board was black and some of the wires had burnt through. I looked around YouTube and found some videos on how to replace the control board and wire harness, and then ordered the parts from appliance parts pros. All in all, it was an easy fix and took me a couple of hours to install the new control board and wire... Read more

Ordered a new Oven Control unit and an Overlay (ours was punctured in a few places -- old and brittle). Opened the stovetop and removed some screws from the front control panel area. Followed the advice from Appliance Parts Pros' video to take a photo of the locations of all the connections on the old panel before removal -- that was an instrumental step to the success of this project! The whole job took just over an hour. Now the over controls and timers work like new -- because they are!... Read more