Hardware Hand Small Engine Start Switch Parts
Bestselling
Price High to Low
Price Low to High
By: Whirlpool
Part Number: WP9763761
If your range burner won't heat, cycles incorrectly, or buzzes when turned on, a faulty infinite switch is likely the cause. Moderately easy DIY repair.
Do-It-Yourself Stories from Customers like You
Stems were broken on handles. Knobs didn't work correctly. Dan R. • Glendale , CA • May 06, 2020
Had to replace both switches. The hard part was getting the control panel off to get access. Only a few screws but even after getting them out, really struggled getting it off. After getting off, discovered that you need to get it lifted up before pulling it off.
Read more
More
By: Ge
Part Number: WR08X10112
Fix compressor clicking every few minutes or fridge not cooling. This start relay and overload combo helps your compressor start and prevents overheating. Easy 5-minute fix.
Do-It-Yourself Stories from Customers like You
Constant clicking sound from behind refrigerator and compressor would not kick on all the time freezer temp was above the desired temperature Peter H. • Bayside , NY • May 10, 2016
I replaced the old capacitor and combo device after watching repair video. Took less than 5 minutes and now my ge profile refrigerator is running perfectly.
Read more
More
By: Frigidaire
Part Number: 318394803
Has three terminals.
Do-It-Yourself Stories from Customers like You
Oven light stayed on when door was closed Robert S. • Jacksonville , IL • June 14, 2015
When trouble shooting the problem I found that the light switch housing outer lip was broken allowing the switch to push through mounting surface behind the oven door. This is a slide in range so, I proceeded to pull the range away from the counter where I could unplug the power cord. Once the power was off like located the panel on the right upper side of the unit and removed the screws to allow access to the switch. I then unplugged the switch from the wiring harness and removed the damaged...
Read more
More
By: Whirlpool
Part Number: 9871829
Fix a compactor that won't start, stops mid-cycle, or requires holding the pedal down. This drawer tilt switch is a quick 15-second replacement.
Do-It-Yourself Stories from Customers like You
Compactor would start sometimes by just closing the door when you start it by normally lifting the pedal it would not stop at the end of it's cycle Bruce H. • Hewitt , NJ • January 19, 2015
I replaced the upper switch that contacts the door in a closed position and more important the start switch contacted by lifting the start pedal.
Read more
More
By: Whirlpool
Part Number: W11206737
Fix a range hood control knob that stops responding or only works in one position. This rotary switch restores precise fan and light selection.
More
By: Ge
Part Number: WB24X10110
Fix a range hood fan that won't turn on or off, or lights that don't respond to controls. This motor/lamp switch restores on/off control. Moderate DIY.
Do-It-Yourself Stories from Customers like You
Broken fan switch William S. • Marco Island , FL • October 02, 2015
Biggest problem was trying to get at the switch to replace it. Had to remove two allen head screws to gain access on the back panel of the range hood. The allen heads were very small fortunately I had a number bits from my old electric screw driver that allowed me to remove them. Even then I had to snake my way cutting my hand to get to the switch to replace it.
The positive part the switch was over $25 less the if purchased directly from GE through Appliance Pros.
Read more
More
By: Whirlpool
Part Number: WPW10274880
Fix a dishwasher that stops mid-cycle with a blinking start light. This door interlock switch restores reliable operation. 20-minute DIY repair.
Do-It-Yourself Stories from Customers like You
Kenmore ultra wash dishwasher worked great for 18 months; then would not run start button blinked 3 times and nothing happened Nick C. • Safety Harbor , FL • November 12, 2015
Looked online, appeared to be door switch or control panel. Tried door switch first, a $30 part. Installed new door switch and washer started right up and appears to be fixed. Have not tried full wash cycle yet, but problem appears to be fixed. I decided to buy part from AppliancePartsPros.com because I could return the part if it did not correct the problem, no one else offered such a deal. I will only deal with AppliancePartsPros in the future, they were extremely helpful on the phone!
Read more
More
By: Whirlpool
Part Number: WPW10285512
Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.
Do-It-Yourself Stories from Customers like You
Temperature control switch failed to cold only. Marilyn M. • Summerfield , FL • September 30, 2017
Replaced with a new one.
Read more
More
By: Whirlpool
Part Number: 279872
This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.
Provides precise resistance to reduce voltage/current in the designated dryer circuit Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model) Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior Replace if visibly burned/damaged or if testing shows an open or shorted condition What's included: One resistor Install notes:
Disconnect power to the appliance before servicing Access the console/wiring harness and note original wire routing Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing After installation, run a test cycle to ensure proper operation of the affected function
Do-It-Yourself Stories from Customers like You
Timer wouldn't advance on my dryer John L. • Oblong , IL • March 22, 2016
I ordered a new timer and installed it with the help of the videos provided and this did not solve my problem so I chated with the pros @ Appliance Parts Pros and told them my problem and they told me the problem and recommended the part I needed and With the incredibly fast shipping I had the part the next day. I installed it and now my dryer timer works great.Thanks to APPs for their help and ease of ordering and fast shipping. I highly recommend AppliancePartPros and will definitely use...
Read more
More
By: Lg
Part Number: EBF60662911
This is a spark ignition switch assembly with wiring harness that controls the electric igniters on a gas range cooktop. It sends voltage to the spark modules when a burner knob is turned, initiating the clicking ignition sequence. Replace this part if your burners won't spark when turned on, spark continuously even when knobs are in the off position, or if only some burners ignite properly.
This part fixes the following symptoms
Doesn't shut off
Gas igniter glows, but will not light
See more...
Do-It-Yourself Stories from Customers like You
All the igniters spontaneously began to fire Michael S. • Adams , NY • October 12, 2019
Found a YouTube video online that provided instruction on how to change out the part.
Read more
More
By: Whirlpool
Part Number: WP3399640
Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.
Do-It-Yourself Stories from Customers like You
My kenmore dryer was not gnitind so therefore no heat also my washer was leaking under the machine Bill K. • Midland Park , NJ • November 24, 2014
THE WSHER WAS EASY BECAUSE THE DRAIN PUMP HAD TWO PENNIES INSIDE IT AND THEY CRACKED THE HOUSING.EASY FIX REPLACING THE DRAIN PUMP. WORKS LIKE A CHARM. DRYER WAS A BIT MORE WORK.I CHANGED THE IGNITER FIRST WITH YOUR ADVICE. STILL NOTHING. I THEN CHANGED THE COIL VALVE KIT. NO LUCK. NEXT WAS THE TEMP SWITCH ON THE PANEL. STILL NO GOOD.FINALLY THE THERMAL FUSE WAS RECOMMENDED. I WAS ABLE TO PURCHASE ONE LOCALLY AND IT WORKED . GREAT RELIEF.THANKS FOR ALL THE HELP AND RECOMMENDATIONS. YOUR...
Read more
More
By: Frigidaire
Part Number: 216594300
The Starter is an OEM replacement part for Frigidaire refrigerators. This component is crucial for initiating the compressor, which is responsible for cooling the refrigerator. The starter works by providing the necessary electrical power to get the compressor running, ensuring that the refrigerator maintains the correct temperature.
Causes of a bad starter can include electrical malfunctions, wear and tear over time, or damage from power surges. A faulty starter can prevent the compressor from starting, leading to cooling issues.
Symptoms of a bad Starter include:
The refrigerator not cooling properly
The compressor not running or frequently cycling on and off
Unusual clicking or buzzing noises from the compressor area
The refrigerator being warmer than usual or food spoiling quickly
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Overload protector done its job we had not defrosted the freezer for a long time causing the compressor to run more than it should it got overloaded found it defrosting Wanda L. • Belle Rose , LA • December 09, 2014
First checked the power then took off the compresser connections cover looked for burnt wires or loose or disconnected wires they were none of those I then removed the wires from the starter an overload protector removed them checked both for contunuaty overload protector no contunuaty then I checked the 3 poles on the comp. for contunuaty they were ok then I checked each pole to ground on the com. to final check that the comp. was still good
Read more
More
By: Whirlpool
Part Number: WP74011489
Fixes burner that won't heat or indicator light stuck on. This infinite switch controls surface burner power and heat settings. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Knob twisted off Glenn M. • Aurora , OR • August 20, 2018
Replaced switch
Read more
More
By: Lg
Part Number: 6600W1K001Q
The Switch, Micro is an OEM part for LG microwaves. This micro switch is crucial for the operation of the microwave door mechanism, ensuring that the microwave only operates when the door is securely closed.
Causes of a bad micro switch can include wear and tear from frequent use, damage due to electrical faults, or physical impact that disrupts its functionality.
Symptoms of a bad micro switch include:
The microwave not starting or stopping unexpectedly
The door not latching properly
The microwave light not turning on or off correctly
Error messages appearing on the control panel
This OEM LG part is also compatible with Sears/Kenmore models.
Do-It-Yourself Stories from Customers like You
Interior light and turntable failed at the same moment. Stacey B. • New Bern , NC • February 01, 2021
Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch.
Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were...
Read more
More
By: Whirlpool
Part Number: 814103
This metal clip secures and stabilizes surface burner components on gas cooktops. It prevents burner parts from shifting during cooking and ensures proper alignment for safe gas flow. Install this clip if burner grates move during cooking, flames appear uneven, or burner parts seem loose or misaligned.
Do-It-Yourself Stories from Customers like You
Two fo the burner retaining clips had broken and one of the burners was malfunctioning Michael G. • Renton , WA • December 05, 2015
It went very easily. The two original clips were riveted in the top but a small drill bit cut the last of the rivit free and the clips remainders just fell out. There was no damage to the stop top. The butner simply snaps in to its socket so that was easy to replace. Pulled the old one out and put in the new one.
Read more
More
By: Samsung
Part Number: DG44-01003A
This is a selector switch that controls a surface burner element on an electric range. It allows you to select different heating zones or power levels for a multi-ring burner. Replace this switch if the burner does not respond to the control knob, only heats on certain settings, or if the switch fails to cycle the element properly.
Do-It-Yourself Stories from Customers like You
Burner indicator light stays on always Joseph S. • Waldron , AR • August 02, 2015
Replaced DG44-01003A (AP4336838) Energy regulator. Fixed it with no problem.
It was the the big burner on my Samsung range that had three settings for pot size.
Read more
More