Power Small Engine Start Switch Parts

I had one element that would operate wide open when turned on the low setting. It needed the switch replaced. Since I was replacing other elements I went ahead replaced them all, adding new drip pans and wiring kits to each new element. Once I replaced everything I was still having issues with the element that had the switch replaced. After further investigation my AC voltage readings were not correct at this element. I traced the problem back to the Molex connector feeding voltage to the... Read more

Put both thermostats in as I did not know if the unit was cycling on high limit at times. Fixed both issues plus I used my lawn blower and blew all the lint out of dryer and short 3' hose. I also lubed rear drum bearings. Works like new. Ron R Read more

After reviewing various posts on the internet, I tested the high heat temperature limiter and determined it was faulty due to lint buildup. Ordered the parts from AppliancePartsPros.com on Friday afternoon and parts were delivered on Saturday afternoon. Replaced the parts- dryer works as good as new. Read more

Replaced those two items listed above, please continue reading! I'm a mechanic by trade, so I have the basics. And what made this job easy? Appliance parts pros! very easy access to Part numbers and Diagrams, Online help, Customer service, and the list goes on. You will see several other sites, However! Wouldn't it be nice, knowing the above? Go no further! If you get stumped on anything during your Maintenance or Repair, They will Help. Read more

Remove bottom panel, remove top panel, remove drum. Had to cut old squirrel cage off. Remove motor to remove old wheel shank. Remove belt switch, and replaced. Videos from AppliancePartPros helped a lot.. Read more

The parts are under the stovetop and the knobs are attached to them. We bought the correct ones from AppliancePartsPros, these were the correct ones. Seems we have an oddball stovetop. It's a GE drop in stove. The parts were easy to change. It was a simple matter of putting the wires on the new switch in the same place there were on the switch. I took phone pics of the wire locations before I took them off and only did one switch at a time. Turn the power off at the breaker panel first of... Read more

I replaced the thermal cut-off sensors and the cutoff-Tml Read more

I have a Bosch nexxt 500 series dryer that stopped heating. It was still running fine, just no heat. I did some research and found the Limiter as the possible problem. I pushed the red reset button. The dryer started heating up, but with in 1 cycle kicked off again. I called A.P.P. and spoke to Cecilia. She was very helpful. After a brief description of my situation she recommended just to replace the Limiter. I did so and that fixed the problem. Very simple replacement. It look longer to take... Read more

New start device. Read more

After the part arrives, I was double check to make sure I got the right part. Importantly, unplug the electrical power first before do anything, also turn off the water hose for safety. Then removed 4 screw out side panel and 2 screw in side to get lose. After all, replaced a new part and put all panel and screw back together. Finally, plug in electrical power then a water hose and test a new part just installed. So far so good, seem like everything was function OK. Again, thanks for your web... Read more

Replaced the switch took a total of about five minutes. I pulled the stove out and turned the breaker off so I only had to pull it out enough to get a 1/4 " nut driver in behind it. Removed three screws and the back cover came off. I pushed the switch threw from the back and switched over the two wires then reversed the process. Completely easy if you can use a screw driver your crazy not to replace it yourself Read more

• Won't start

First, it was going to cost $95 for an appliance guy just to look at it! I figured there would be an upcharge on the parts + labor on top of the $95, so I took a chance & decided my husband & I could fix it cheaper; we were right, but it was a 3 week process (luckily, we have another microwave in the basement we were able to use in the meantime). I googled the microwave model #, then price checked the same item I thought we needed; printed off the diagrams of the various microwave "systems" &... Read more

I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more

Replaced the fabric selector switch. Took abut fifteen minutes. Dryer works fine. Read more