Hardware Hand Small Engine Ignition Coil Parts

Need to open because no parts’ numbers can be identified through their website. But the rest “order and put in” are very easy steps. Will come back if I do need other parts Read more

• Little to no heat when baking

I removed two screws at rear of oven, disconnected electrical connectors, and removed old element. When the new element arrived (on time), I connected the new element and replaced the two screws. The oven worked perfectly! The repair was extremely easy and cost effective. Read more

Firstly, the Ice Door had a kink in the edge, which caused it to stay open and create lots of frost on the coils. $5.00 part, highly recommend it. (By the way, the new door was little too big and it too stay propped open and left a gap so I had to trim the top edge of the rubber with scissors to get it to fully close.) Secondly, there are two heaters for the defrost cycle, one that goes around the coils and another attached to a collector pan beneath the coils. When the cycle hits, those... Read more

It went very easily. The two original clips were riveted in the top but a small drill bit cut the last of the rivit free and the clips remainders just fell out. There was no damage to the stop top. The butner simply snaps in to its socket so that was easy to replace. Pulled the old one out and put in the new one. Read more

So I ordered the burner and Ithe switch because I wasn't sure what part was defective. I pulled the oven out and I removed the 6 1/4 inch screws on each side of the glass top as well as the 2 Phillips head screws on the back, removing the 2 1/4 screws on the shield on the back gIves you easier access to them, then lifted the glass top up on the front to access the switch and burners. Make sure you turn the power off before beginning this process. When lifted up the wires connected to the... Read more

Ordered the OEM conversion kit from you guys Read more

It was very easy!. Just removed the screws off the trim plate and access was right there. The double oven was given to me but the handles were missing and the end caps so I just had to replace them. Read more

First replaced defrost timer which tested OK - but reasonable price and easy to replace. When that did not fix the problem replaced the defrost thermostat and defrost heater. That fixed the problem. However all three parts tested OK ?? May have been a loose connection or intermittent problem with one of the parts. Final cost for all three parts was much cheaper than a service call!! Read more

Ordered the replacement part the recommended by your parts department. I then watched a video so I knew what was in Store. The part arrived in less than 2 days & 15 minutes later I was baking brownies!!!!! Voila!!! Done deal!!! Now I am going to order a second one to replace the lower oven's element since it's been 'off' for over a year. The local appliance repair had informed us that it would charge $125 for the initial 30 minute service call to come in to inspect the appliance,... Read more

I ordered the both the Pcb assembly and a heater sheath. Upon accessing the Pcb, I immediately discovered it had failed miserably, (contacts burnt and melted, wiring and insulation on one wire suffered severe electrical damage. To put it bluntly a small electrical fire had occurred on the circuit board. There was enough slack in the damaged wire so I removed the affected area, replaced the terminal. Replacing the Pcb was a snap. Disconnect the power, remove the rear cover, prior to removing... Read more

Who does that? I've lived in my house for many years and never have done the damage that a renter can do in just 1 year. Looked up the Serial number and found the parts I needed easily. Ordered them and they arrived in about 3 days. Fit perfectly. Read more

• Will not drain

Removed upper frig & lower freezer back evaporator covers to get to the frost buildup on the evaporator assembly. I then used a paint stripper heat gun to melt the ice build up caution should be used to keep the gun moving around as not to damage Wires,Eva,Sensor's. After 15 to 20 min of clearing frost I was ready to replace Drain Plate's & Thermal fuse's. When I had removed the old Defrost Thermal fuse's in the refrigerator & the freezer they looked different! They had an insulating foam... Read more

Replace the element. Read more

Replaced the entire burner. Four screws to remove front hinged pane lon front of stove One screw on each end of support bar for burners, Two clips holding burner on support bar. Two connections to burner. Four connections to thermostat.Remove all and replace in reverse order. New part requires one jumper wire on burner. Read more

The parts look great!!! Easy to put in....And parts came in 4 days..... Read more