Starter Relay Parts

Refrigerator not cooling or making clicking sounds? This compressor relay and overload kit fixes starting issues. DIY repair takes about 30 minutes.

This 3-position temperature switch selects the dryer's heat level so the appliance reaches the desired drying temperature. It replaces a worn or faulty selector to restore proper temperature selection and consistent drying performance. What it does:

• Switches between three temperature settings to control dryer heat levels.
• Routes power to the heater circuit based on the selected heat setting.
• Commonly replaces a switch that causes incorrect heat, no heat on some settings, or inability to change temperature.
• Works with the dryer's control system and thermostats to maintain selected drying temperature.

• Disconnect power to the appliance before attempting any service.
• Handle terminals and connectors carefully; match wiring to original locations or take a photo before removal.
• Verify operation with a multimeter for continuity per service manual before and after installation.

This potentiometer kit is the user-adjustment control the appliance reads to set operating levels. Replacing a worn potentiometer restores smooth, predictable response when you turn the knob, helping the control register settings accurately.

• Varies electrical resistance so the control can interpret knob position
• Helps set functions such as speed, power level, or temperature as designed
• Failure can present as no change when turning the knob, jumpy/erratic response, or settings stuck at one level
• Can also cause intermittent operation or "dead spots" while adjusting

• Disconnect power to the appliance before servicing
• Access the control area; note wire positions or take a photo before removal
• Transfer any knob/shaft adapter from the old part if applicable; secure the new pot without over-tightening
• Route wiring away from sharp edges and heat sources; verify proper operation before reassembly

This infinite switch controls the heat output of a surface burner element on an electric range by cycling power on and off at varying intervals. It allows you to select and maintain a specific temperature setting for the burner. Replace this switch if a burner stays on high regardless of the knob position, won't heat at all, or provides inconsistent temperatures.

Burner won't spark or ignite? This ignition switch controls the spark module for gas range surface burners. Mounts on the valve assembly behind knobs.

This infinite control switch regulates the heat output of a surface burner element on an electric range. It connects to the burner element wiring and allows you to adjust the cooking temperature from low to high. Replace this switch if a burner stays on one heat level regardless of the knob position, won't turn off, or doesn't heat at all.

Fix a dual burner that won't heat or lacks proper temperature control. This infinite switch restores heat regulation for accurate simmer-to-boil cooking.

Fix washer temperature issues with a new selector switch. Solves problems when hot or cold water won't flow correctly or temperature settings don't respond.

This replacement switch restores reliable on/off control for the matched function in your appliance. A worn or sticking switch can prevent components from powering correctly; replacing it helps bring back consistent, safe operation.

• Opens and closes an electrical circuit to control a specific component
• Actuates via a knob, button, lever, or door/lid mechanism
• Common symptoms: unit or component won't start/turn on, intermittent operation, or must press/hold to work
• Visual clues: loose actuator, heat discoloration, or burned terminals

• Disconnect power before servicing; verify no voltage with a meter
• Document wire positions; move leads to the new switch one at a time
• Secure the switch in the original orientation and ensure proper actuator alignment
• Restore power and test the controlled function for proper operation

If your washer overfills, underfills, or won't advance cycles, the water level pressure switch likely failed. This DIY repair restores proper filling.

Fix a washer button that won't respond, works intermittently, or sticks when pressed. This pushbutton switch restores on/off control for your appliance.

Fix burner clicking without sparking or nonstop clicking with this valve switch. Restores spark ignition when you turn the knob to Lite. Easy DIY repair.

Fix a dishwasher that won't start, has no lights, or only runs certain cycles. This switch assembly restores proper signaling to the control board.

Fix a refrigerator that clicks but won't start or cycles on and off repeatedly. This compressor start relay powers the start winding for reliable cooling.

Fix a trash compactor that won't turn on or off with this control switch. Direct replacement part installs in minutes with basic tools.

Refrigerator clicking but not cooling? A failed compressor start device causes repeated clicking and warm temps. Quick DIY fix restores reliable starts.