User Control Display Board Parts

Fix a dishwasher that won't start, stops mid-cycle, or has dim lights with a new electronic control board. Moderate DIY repair, 45-60 minutes.

Refrigerator freezing food or not cooling? This temperature control thermostat regulates cooling cycles. Common DIY fix when temps won't stay consistent.

Electronic control panel touch pad for upright freezers. Mounts on the front door. Replace if buttons are stuck, unresponsive, or the display is damaged.

This is a relay control board that manages the switching of electrical power to heating elements and other high-voltage components in the oven. It receives signals from the main control board and activates or deactivates the appropriate circuits. Replace this board if the oven elements fail to heat, heat intermittently, or if you notice error codes related to relay or heating circuit failures.

This OEM replacement part is an oven control board. The oven control board is the primary computer circuit board that controls the main functions of the oven. These functions include turning the oven on as well as adjusting and maintaining the temperature of the oven. Luckily, replacing a control board is a simple process.To replace the board, first, make sure the oven is unplugged. Gain access to the back of the oven and remove the upper back panel. Once the panel is removed, locate the old control board. Take note of the orientation of the wires by taking a photo with a phone camera. Disconnect the wire harness and any individual wires that are attached to the old board. Re-secure the wires into their correct positions. Snap the new board back in place and reinstall the upper back panel.This genuine replacement control board is compatible with Frigidaire Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

Washer won't advance cycles, keeps filling, or skips rinse/spin? Timer controls cycle sequences. Moderate DIY repair restores proper wash timing.

This coin chute guides coins from the slide into the coin mechanism so the machine can register payment and begin a cycle. Keeping the chute intact and aligned helps prevent jams and misfeeds in coin-operated laundry equipment.

• Directs coins from the slide to the coin mechanism to register payment
• Helps ensure smooth coin drop, reducing bounce-back and misfeeds
• Common fix when coins jam, fall into the cabinet, or the unit won't start after payment
• Replace if cracked, bent, corroded, or missing

• Disconnect power; shut off gas before service
• Open the coin housing/slide assembly and retain existing hardware
• Install the new chute in the same orientation; align with slide and mechanism, then secure
• Test with sample coins to ensure proper drop and operation before returning to service

This control panel assembly replaces the white front console on your dryer. It restores a solid mounting surface for the timer, switches, or display so you can select cycles and settings with proper alignment and smooth operation. What it does

• Provides the front console housing for the dryer's user controls
• Keeps buttons/knobs and indicators aligned and protected
• Restores appearance after cracks, discoloration, or broken tabs
• Helpful when controls feel loose, are hard to press, or the console is rattling

• 1 white control panel assembly

• Disconnect power; if gas, shut off the gas supply before servicing
• Remove control knobs and any end caps; take out mounting screws/clips and lift off the old panel
• Transfer any brackets, light pipes, clips, and harness retainers from the old panel to the new as needed
• Reinstall and tighten fasteners; refit knobs and verify smooth control operation before restoring power

Fix a dryer that won't advance cycles or turn on due to a worn timer shaft. This plastic-shaft timer restores knob grip and timing control. 10-minute DIY fix.

This thermostat regulates the internal temperature of the refrigerator by cycling the compressor on and off based on the temperature setting. It connects to the temperature control dial or knob inside the fresh food compartment. Replace it if the refrigerator runs constantly, doesn't run at all, freezes food in the fresh food section, or fails to maintain the correct temperature.

Dryer won't shut off or advance through cycles? This timer restores proper cycle switching and automatic shut-off. Moderate DIY repair, 30-45 minutes.

Washer won't start, shows error codes, or cycles randomly? The main control board manages all wash functions. Moderate DIY repair with careful handling.

Refrigerator not cooling or ice maker stopped working? This main power control board manages core functions and power distribution. DIY-friendly repair.

Cracked or damaged control panel trim? This escutcheon covers and protects control switches from grease and spills. Simple install, reuse screws.

Fix cracked or melted control panel housing. This board housing assembly secures your oven's electronic control board. Moderate DIY repair, under 1 hour.

This replacement control panel, also called the backsplash assembly, is the structural console on the rear of the dryer top where the timer and switches mount. It restores secure control mounting and a clean, finished appearance when the original is cracked or damaged.

• Houses and supports the dryer's timer and control switches
• Covers and helps protect console-area wiring from contact
• Aligns control shafts through the panel openings for smooth knob operation
• Common signs of failure: cracked panel, broken mounting tabs, loose or rattling controls

• Disconnect power; for gas models, also shut off the gas supply
• Remove control knobs and mounting screws, then tilt or lift the console to access the panel
• Transfer timer/switches and any brackets from the old panel to the new one, keeping hardware organized
• Do not overtighten screws; verify all controls turn and click freely before restoring power