Lid Lock Switch Parts

• Door won't close

There is a video on youtube that talks about how to disassemble the electronic component out of the control board so I really won't go into that part of it. This disassembly of the control board will need to take place before you can even get started taking the gray piece out of the console to replace it. Be careful not break off the little tips behind the control knob, don't force it, it does come apart easily and there is an easy way to do it, that is also on youtube. This is where the... Read more

• Element will not heat

Replaced all four element switches. Switches arrived within two days of ordering. That's about normal for AppliancePartsPros. They were the correct ones; not generic, and fit the original control knobs perfectly. This kind of service is what I'm used to from ApplicanePartsPros. Read more

• Door won't close
• Door stuck closed

This was much easier than expected. I called Appliance Parts Pros with my model # and you told me what part I needed. It was shipped the same day and arrived the next day. I removed the inner door trim with a table knife ( don't rush this or you might crack the trim ). I then unhooked the old door latch disconnected the spring from the door hooked on the spring from the new latch and clipped in the latch to the door. Final step was to reattach the door trim. It was very easy and all I used... Read more

We ordered a door switch, dryer latch and strike plate. We realized that we only needed to replace the door switch. We watched a few videos and then replaced the switch. We couldn’t find a video for our model but they did give us a pretty good idea about what we needed to do. The hardest part was getting the original door switch out, all of the videos we watched showed us that it would pop out with a little pressure from a flat head screw driver, from the front of the switch. We could not get... Read more

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

Unscrewed the stove top, unplugged the connections, removed the stovetop. Replaced the burner and the switch. Put it back together again. Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

• Doesn't shut off
• No heat
• Won't start

The first symptom was our microwave would continue to run after the time was up. The light would go out, the turn table would stop but you could still hear the microwave running and whatever was in it would continue to cook. The only way to stop it was to open the door. It was intermittent at first but eventually it would always run no matter what as long as the door was closed. Several other posts referenced these switches as the problem. I just replaced both and problem gone. It turns out... Read more

Conducted research on web, and via direct contact with AppliancePros where a diagnosis of replacing the water inlet valve and cleaning the sensor tube would "most probably" (80%) handle the issue. The remaining uncertainty would reside in the electronic board circuitry. The price of replacing the water inlet valve was half of a local repair call just to diagnose the issue so I decided to have faith in the odds presented to me. The part arrived on time, and using AppliancePros advice and... Read more

After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more

Watched a You Tube video on how to remove the bad lid lock, ordered a new part and installed. Read more

Replaced it. Read more

I contacted AppliancePartsPros and gave them my symptoms and failure codes and they were able to diagnose the problem and send the correct parts to resolve the issue. This is the 3rd or 4th time I've used their service since 2012 and they have been correct on each and every repair issue I've had. Many thanks for the professional advice and help! Read more

Replaced door switch - it took less than 5 minutes - works perfectly Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

• Won't start
• Will not drain
• Will not fill with water

First, I ordered the wrong part (not paying attention to the model number on my machine...) I installed the part, following the very excellent video instructions from the website. I got the machine all put back together, but the electrical connection did not match! So, just a few days from leaving on vacation, I chatted online with the representative, Robyn C., from AppliancePartsPros.com. She was so helpful, double checking that the model number of my machine matched the new part, and... Read more