Run Vent Thermal Fuse Parts

Conducted research on web, and via direct contact with AppliancePros where a diagnosis of replacing the water inlet valve and cleaning the sensor tube would "most probably" (80%) handle the issue. The remaining uncertainty would reside in the electronic board circuitry. The price of replacing the water inlet valve was half of a local repair call just to diagnose the issue so I decided to have faith in the odds presented to me. The part arrived on time, and using AppliancePros advice and... Read more

• Shuts off too soon
• Too hot
• Takes too long to dry
• Won't start

Recommendations have fun and a bucket to prevent losing parts. First watch the videos, practice disassemble and reassemble the dryer drum. Make certain you have a good screw driver and spatula from kitchen (could not find my putty knife). Secondly, clean and inspect everything, make sure the motor bearing and belt pulleys are in good condition with little or no play. Third after you have confidently disassembled, vacuum cleaned, inspected all the worn parts, grease the motor and pulley,... Read more

• Fridge too cold
• Freezer too cold
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

Replaced fan motor in fresh food section, easiest repair I have ever made, took longer to get shelves out than replacing motor.. Read more

I think I have a lemon of a dryer. I keep having to pay someone to replace my heating element about every year. So I already had the heating element, but I thought I would replace the thermostat and the limiter also. Yes, I am a 46 year old mom, and I replaced all three items. Thank goodness to youtube! Ha! I have ordered from you before and you always send promptly. Thanks! Read more

I found a video, by another parts vendor, that showed in detail how to dismantle and repair the washer. I wouldn't have known how to even get to the problem without that repair video. Dismantling the washer was easy once I knew how, but would have been like a (litteral) Chinese puzzle without the video. Once I had cracked open the machine and identified the problem, the repair was easy. I ordered from Appliance Parts Pros because they offered next-day delivery of parts. I had the washer back... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

****** always make sure the unit is fully unplugged from the power before you do anything with the outside of the unit to work inside of the unit and while you are working inside the unit... Also make sure that you turn the hot and cold water intake valves off and make sure you don't pull too much on the two water intake hoses that lead to your washer because they can leak with too much pressure exerted on either end******* 1. Took top off unit by unscrewing mounting brackets at two similar... Read more

Purchased, Igniter Kit, Gas Valve Coil Kit, and as a precaution Thermal Fuse and Cutoff-Tml. Was pretty confident the problem was the gas valve coil, but figured that why not just replace the other items while I had the unit apart. Researching and utilizing this site certainly helped me out in figuring what the problem may be. Watched the instruction videos which were very detailed and helpful. The replacement and repair was not that difficult and the work was done rather quickly. Doing... Read more

We replaced the main circuit board and the LED started to work and the condenser fan worked, but all we had were relay clicking sounds, but no cooling. The compressor had become so hot trying to work when the main circuit board was amiss, that it had popped the over temperature sensor on its side. As some one point out, if you remove the PTC+OLP assembly with the capacitor on it, and shake it, you will hear a rattle inside---and that is bad. We ordered a second round of parts from... Read more

Replaced heating element and thermostat, took me about 2 hours but that's because i had to vacuum out the dryer inside and I also checked the fan before I closed the dryer back up. I have a Samsung DV448AAEP. Works great and saved my family money! Read more

• No heat or not enough heat

Replaced the inlet control thermis (thermostat) . Now it completes the cycle but clothes are not 100 % dry. I would add 15 minutes more and that helps. FYI: you don't need to remove the drum, just remove the top cover and that will give you enough space to replace the sensor Thank you Appliance Parts for your fast speed of delivery. Read more

First and foremost, much thanks to APP for perfect transaction, and incredible price! The part was shipped quickly, and arrived fast. Immediate Availability of the part was outstanding, and truly saved this Canadian's day! See, in Canada, LG has their own unfair practice of NOT ALLOWING a Canadian citizen to purchase ANY functional parts for any of their appliances or products... furthermore, in order to get the part for any issue, you must pay directly for an LG direct service tech to come at... Read more

Replaced the Thermal Fuse on the dryer. Read more

My wife said we have a problem with our dishwasher (Whirlpool WDT920SADE2). The dishes were not getting clean, and the soap dispenser opened, but soap was still dribbled down the inside of the door and on the silverware caddy. I'm not the handiest guy; it took me several days to go through the trouble-shooting process, watching multiple videos and trying different things. My initial guess was that the soap dispenser was opening too late. (This turned out to be wrong.) I started off by... Read more

• Too hot
• No heat or not enough heat
• Takes too long to dry

Replaced thermal stats Read more