Kitchen Vent Parts

I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more

REMOVED BACK PANEL, USED PLYERS TO REMOVE CLAMP, PULLED OLD HOSE OFF, REVERSED PROCEDURE TO INSTALL NEW HOSE. TOTAL TIME ABOUT 10 MINUTES. Read more

This hose did not just attach to the back of the washer--that would have been too easy. This hose went into the back of the washer, under the tub & attached to the pump at the front of the washer. Both the back & front of the washer had to be removed to access the hose. Luckily the crack was at an external spot where it was easily seen; unluckily my husband was out of town at the time & I had to take the washer apart & put it back together. Actually it was not that hard. Before I took the... Read more

Our GE front loader dryer is approximately 10 years old. It started making a loud noise. Before we sank another $600 for a new dryer, I decided to go online to search Youtube videos to try to find out if anyone else had the same problem. I found that a lot of dryers had drum support bearings that wore out and needed to be replaced and a lot of dryers were also having clothes caught up in them. I then found an Appliance Parts Pro video on how to fix this problem and found out what parts... Read more

• Will not fill with water
• Leaking

SCREWED IT ONTO FAUCET Read more

Condenser fan motor sounded like a dying animal. Ordered a new motor, fan blade and grommets. The fridge sounds so much better, it's hard to tell it's on. Took 20 minutes, most of it cleaning. Read more

After watching a number of videos and reading a lot of trouble-shooting discussions online I had ideas of what to look for as possible causes of the overfilling of the drum. I found the water level pressure hose had worn through after contacting the rotor. After temporarily taping the hose, I found the service manual inside the machine so I ran it through it test sequences without any error codes. Suggesting the hose and not the sensor or inlet valves were the problem. I ordered parts last... Read more

Our washing machine door boot seal was getting moldy and causing odor problems. Cleaning tablets and bleach weren't helping so it was time to be replaced. While I had the top and front off I changed all the hoses that could be collecting soap scum and mold, all other wetted parts were removed and washed. The video on the door boot seal, and inlet valve assembly were extremely helpful in understanding how these parts are removed and reassembled. Although the door boot seal is the most visible... Read more

Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly. Now we're washing again and no leaks! Read more

Replaced the drain pump and the drain hose (since I was replacing the drain pump). The new drain pump seems to pump out the water more forcefully than the one replaced. Have not received a LD code during the wash cycle since the replacement was installed. Read more

Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more

First of you need to remove front panel of the washer, using a putty knife push the tabs between the top of the machine and the front panel. Once front panel is exposed drain hose is connected to pump which is in the front of the machine,very easy to access with the front off. Remove old hose with pliers and discard ,run new hose thru outlet on the back of the machine and secure new hose to drain and secure hose to the machine, reinstall front panel of washer and that's it Read more

Replaced flow meter and control valve Read more

I replaced the drain pump and hose which had a flapper valve that wasn’t sealing properly. Easy repair. Took about 15 minutes total and my washing machine is Soooo much quieter!!! Read more

First of all, I want to say that this is not the first time that I have used AppliancePartsPros. They give you everything you need in the most simplified manner to repair your appliances at home. I ran my washer until I started to see the leak coming from underneath. After verifying that the intake hoses, drain hose and pump were not leaking, I opened up the washer from the top by unscrewing the two screws on the back brackets and lifting up and out. Because the leak was displaying at the... Read more