Fin Plate Parts

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

Samsung top load washer, about 3 years old started throwing a DC error code more and more often. Initially started with large loads. Wash would get to spin cycle, start wobbling all over the place, stop and refill then try again. Eventually it would stop and throw the DC code. As time went on, the size of the loads got smaller and smaller. Research here indicated that suspension rods probably need replacing. I bought 4 rods for replacement for about $90 in total inc. tax & shipping.... Read more

I discovered that the manifold was not connecting with the water supply,so the dishes in the upper tray were not being washed. This was caused because the rear hanger on the manifold had broken and it did not lineup properly into the water supply connection in the back of the dishwasher. I removed the manifold and found that it had two part numbers stamped on it. I searched on both part numbers and received a hit on the second part number. The photo looked exactly like my manifold so I... Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more

Ordered parts Read more

I replaced all 4 suspension rods and springs and now it spins very smooth. They weren't broken, just badly worn. It gave new life to my 15 year old GE Profile washer. They are basically springs, so they wear after a while. It was well worth the hour I spent fixing it. You need a good long reach to get to the back 2 and you have to take off the dampening straps and the control panel so you can gain access. All in all, I'm happy with the repair, although I though that these parts are bit... Read more

• Shakes and moves

After watching the video carefully and taking notes for step-by-step dismantling of the LG washer, I took it apart methodically placing each item on a table in the order removed. I was able to remove and replace the bearings with no problems following the tips and tricks. The spider did not seem to be in bad shape but since I had a new one, it seemed reasonable to replace it as well, but it was difficult to extract the old one from the drum. The bolts are assembled with weld glue, so it is a... Read more

No tools required. One item was defected but Appliance parts replaced it immediately. Read more

Chopper screen was completely blocked. Chopper blades separated from the shaft. Retainer ring came off of the shaft but was able to re install the chopper assembly. Worked fine after cleaning the screen and reassembly the lower spray arm. Lower spray arm hub tab broke when removing so purchased a new one with a new bearing. Appliance Part Pros video was excellent and very helpful. Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

After taking off the top and front panels to access the drum, it was easy to see what the problem was. The front drum support was worn through and the 3 drum support glides were gone. The rear drum bearing was also completely worn out. And while I had the dryer apart I also replaced the idler pulley and drive belt. The only hard part was putting the drive belt back on the motor shaft and idler pulley. The dryer is back to drying clothes like a new machine. Read more

This was a simple fix since mine didnt need any screws. Slipped in and locked into place. Read more

Easy project. 6-year-old appliance. If one is failing replace all 4. The plastic race that holds the bearings becomes brittle and breaks dropping the bearings into the dishwasher tub. Total project time from assembling tools, protecting the hardwood floor, removal, and installation was less than 2 hours. 1) Turn off power to the appliance. 2) Remove 2 mounting Phillips screws holding dishwasher in the cabinet. 2) use a 1/4” nut driver to remove the 2 screws holding the bottom plate from... Read more

I tore it apart using. YouTube videos to guide me and found the shocks were loose and floppy. I found the shocks in stock here and had them in my hand 2 days later for only $10 shipping! It runs great now! Read more